Morehouse 4215 Скачать руководство пользователя страница 17

Страница: 17 / 50

Morehouse Instrument Company, Inc.

1742 Sixth Ave., York, PA 17403-2675 USA

Phone: (717) 843-0081

www.mhforce.com

Page 17

Rev. 3/2022

4215-HS Indicator

Manual

(PM-4101)

>>Com Baudrate

This sets the baud rate for the RS232 ASCII command set. Available values are: 300, 600, 1200, 2400, 4800,

9600, and 19.2k. Note that the “Special” entry is reserved for future use.

>>Com Line Feed

This controls whether a line feed is added to each carriage return that is sent out by the Model 4215-HS when

the RS232 ASCII command set is being used.

>>Retain Tare

This controls whether the most recent tare value is retained through power down of the unit and used again

immediately on power up. Choosing this option will retain tare on channel A in a single channel unit and both

channels A and B in a twochannel unit.

>>Display Options

This menu contains options that effect how load, peak, and valley are displayed and printed. These are listed in

a submenu that works exactly like the setup mode main menu.

>> Filter Select

There are two types of filters available on the Model 4215-HS: Type I, and Type II. Type I filters are good for

removing most kinds of noise but may leave some jitter on the end digits. Type II are more advanced filters

that are optimized for the typical industrial environment. Both filter types allow you to select from 4 levels of

filtering with Level 1 being the least filtering and Level 4 being the most filtering.

The settling time for each of the 4 levels of filtering is shown in the table below.

Level

Setting Time (seconds)

Read Rate (per second)

Содержание 4215



















































Результаты поиска

Содержание 4215

Отзывы:

Похожие инструкции для 4215

Бренды по названию

Популярные бренды

Morehouse 4215, Руководство по эксплуатации и инструкция

Результаты поиска

Содержание 4215

Отзывы:

Похожие инструкции для 4215

Бренды по названию

Популярные бренды