Morehouse 4215 Скачать руководство пользователя страница 6

Страница: 6 / 50

Morehouse Instrument Company, Inc.

1742 Sixth Ave., York, PA 17403-2675 USA

Phone: (717) 843-0081

www.mhforce.com

Page 6

Rev. 3/2022

4215-HS Indicator

Manual

(PM-4101)

The Model 4215-HS has three modes of operation, Run mode, Setup mode, and System Calibration mode. At

power-on it will be in Run mode.

The first line of the display show an item label (Load A), a value (0.0000), and a unit label (Lb).

The second line of the display can show the status of the 4 contact closure limit switches, show another dis

play, show text, or be blank.

To change what item is being displayed press the leftmost button. This will cycle through the list of items (Load

A, Peak A, Vall A, Load B, Peak B, Vall B, Pos, Vel, and Limits, optionally Avg A, Avg B).

The rightmost button will change the units that are being used. Repeated presses of this button will cycle

through the list of units available for the currently displayed item. For example, with Load showing you would

see Lb, kg, N, PSI, MPa, Klb, kN, t, mV/V, g and then back to Lb.

The table below summarizes the options.

All of these measurements are acquired by the Model 4215-HS at all times. The display just selects which par

ticular item you wish to see and what units are used to display or print this data.

The row of buttons have the functions indicated by the upper set of labels (Item, Tare, Reset, View, Print, Unit).

Each of these is described below.

Message

Meaning

Load A

Pounds, Kilograms, Newtons, PSI, MegaPascals, Kilo-Pounds, Kilo-Newtons, Metric Tons, mV/V, grams.

Peak A

Pounds, Kilograms, Newtons, PSI, MegaPascals, Kilo-Pounds, Kilo-Newtons, Metric Tons, mV/V, grams.

Valley A

Pounds, Kilograms, Newtons, PSI, MegaPascals, Kilo-Pounds, Kilo-Newtons, Metric Tons, mV/V, grams.

Load B

Pounds, Kilograms, Newtons, PSI, MegaPascals, Kilo-Pounds, Kilo-Newtons, Metric Tons, mV/V, grams.

Peak B

Pounds, Kilograms, Newtons, PSI, MegaPascals, Kilo-Pounds, Kilo-Newtons, Metric Tons, mV/V, grams.

Valley B

Pounds, Kilograms, Newtons, PSI, MegaPascals, Kilo-Pounds, Kilo-Newtons, Metric Tons, mV/V, grams.

Position

Inches, Centimeters, Percent of Base Length.

Velocity

Inches per Minute, Centimeters per Minute.

Limits

Shows state of each switch, 1 for on, 0 for off, dash for disabled, asterisk for source error.

Avg A

Pounds, Kilograms, Newtons, PSI, MegaPascals, Kilo-Pounds, Kilo-Newtons, Metric Tons, mV/V, grams.

Avg B

Pounds, Kilograms, Newtons, PSI, MegaPascals, Kilo-Pounds, Kilo-Newtons, Metric Tons, mV/V, grams.

Run Mode

Содержание 4215



















































Результаты поиска

Содержание 4215

Отзывы:

Похожие инструкции для 4215

Бренды по названию

Популярные бренды

Morehouse 4215, Руководство по эксплуатации и инструкция

Результаты поиска

Содержание 4215

Отзывы:

Похожие инструкции для 4215

Бренды по названию

Популярные бренды