Moons' MSSTB05-C Скачать руководство пользователя | Manualshive

Страница: 13 / 25

background image

13

Rev. 1.0

09/06/2015

MSSTB-R/C Hardware Manual

400-820-9661

2.5 Connecting the Power Supply

Connect power supply “+” terminal to the drive terminal labeled “V+”.
Connect power supply “-” terminal to the drive terminal labeled “V-”.
MSSTB05 accepts DC voltage range from 24 – 48VDC
MSSTB10 accepts DC voltage range from 24 – 70VDC

Warning: DO NOT reverse the wires
NOTE: DO NOT apply power until all connections to the drive have been made

V+

J1

V-

Power Connector

Ensure a proper earth ground connection by using the screw on the left side of the chassis.

To Earth Ground

Please read “choosing a power supply” for more details.

«
...
11
12
13
14
15
...
»

Содержание MSSTB05-C


























Отзывы:

Нет отзывов

Похожие инструкции для MSSTB05-C

Бренд: QPS Страницы: 16

MILLENIUM 351-46

Бренд: York Страницы: 24

CMMT-AS-C12-11A-P3-EC-S1

Бренд: Festo Страницы: 16

Бренд: Graco Страницы: 4

Бренд: Parker Страницы: 54

Бренд: China EM Technology Limited Страницы: 94

B-Tronic VarioControl VC4200B

Бренд: Becker Страницы: 20

Бренд: Label Страницы: 56

Бренд: Eaton Страницы: 27

Бренд: Veichi Страницы: 520

Бренд: Nitto Seiko Страницы: 30

Бренд: Leadshine Страницы: 28

Бренд: Leadshine Страницы: 59

Бренд: AMCI Страницы: 74

Бренд: YASKAWA Страницы: 288

Бренд: EUCHIPS Страницы: 4

apfiff09 marine

Бренд: Vacon Страницы: 310

Бренд: EACON Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды