Moons' MSSTB05-C Скачать руководство пользователя

Страница: 5 / 25

Rev. 1.0

09/06/2015

MSSTB-R/C Hardware Manual

400-820-9661

1.3 Safety Instructions

Only quali

ﬁ

ed personnel should transport, assemble, install, operate, or maintain this equipment.

Properly quali

ﬁ

ed personnel are persons who are familiar with the transport, assembly, installation,

operation, and maintenance of motors, and who meet the appropriate quali

ﬁ

cations for their jobs.

To minimize the risk of potential safety problems, all applicable local and national codes regulating

the installation and operation of equipment should be followed. These codes may vary from area

to area and it is the responsibility of the operating personnel to determine which codes should be

followed, and to verify that the equipment, installation, and operation are in compliance with the

latest revision of these codes.
Equipment damage or serious injury to personnel can result from the failure to follow all applicable

codes and standards. MOONS

’

does not guarantee the products described in this publication

are suitable for a particular application, nor do they assume any responsibility for product design,

installation, or operation.

•

Read all available documentation before assembly and operation. Incorrect handling of the

products referenced in this manual can result in injury and damage to persons and machinery.

All technical information concerning the installation requirements must be strictly adhered to.

•

It is vital to ensure that all system components are connected to earth ground. Electrical safety

is impossible without a low-resistance earth connection.

•

This product contains electrostatically sensitive components that can be damaged by incorrect

handling. Follow quali

ﬁ

ed anti-static procedures before touching the product.

•

During operation keep all covers and cabinet doors shut to avoid any hazards that could

possibly cause severe damage to the product or personal health.

•

During operation, the product may have components that are live or have hot surfaces.

•

Never plug in or unplug the Integrated Motor while the system is live. The possibility of electric

arcing can cause damage.

Be alert to the potential for personal injury. Follow recommended precautions and safe operating

practices emphasized with alert symbols. Safety notices in this manual provide important

information. Read and be familiar with these instructions before attempting installation, operation,

or maintenance. The purpose of this section is to alert users to the possible safety hazards

associated with this equipment and the precautions necessary to reduce the risk of personal injury

and damage to equipment. Failure to observe these precautions could result in serious bodily

injury, damage to the equipment, or operational dif

ﬁ

culty.

Содержание MSSTB05-C


























Результаты поиска

Содержание MSSTB05-C

Отзывы:

Похожие инструкции для MSSTB05-C

Бренды по названию

Популярные бренды

Moons' MSSTB05-C, Руководство по оборудованию

Результаты поиска

Содержание MSSTB05-C

Отзывы:

Похожие инструкции для MSSTB05-C

Бренды по названию

Популярные бренды