Monessen Hearth AVFL Series Скачать руководство пользователя страница 3

Страница: 3 / 44

AVFL Vent Free Fireplace

Monessen • AVFL42NIP-SR Installation Instructions • 4119-900 Rev. B • 05/20

Customer:

Lot/Address:

Model

(circle one):

AVFL42N

IP-SR

Date Installed:

Location of Fireplace:

Installer:

Dealer/Distributor Phone #

Serial #:

Comments:

Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective

action needed _____________________________________________________________________________________

Comments Communicated to party responsible ____________________ by ______________________on ___________

(Builder / Gen. Contractor/) (Installer)

(Date)

___________________________

4119-982

04/20



= Contains updated information.

• Photographing the installation and copying this checklist for your file.

• That this checklist remain visible at all times on the appliance until the installation is complete.

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this

installation manual.

WARNING! Risk of Fire or Explosion!

Failure to install appliance according to these instructions could

lead to a fire or explosion.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Appliance Install

(

Pg.

-12

)

Verified that the chase is insulated and sealed.

Required non-combustible board is installed.

Verified

clearances to combustibles.

Fireplace is leveled and secured.

Adequate provisions for combustion and ventilation air have been verified.

Gas

(Pg 1

-1

)

Proper appliance for fuel type.

Leak check performed and inlet pressure

verified.

Verified proper air shutter setting for installation type.

Electrical (Pg

)

Unswitched power (110-120 VAC) provided to the appliance.

Switch wires properly installed.

Media & Accessories

(Pg

17-21

)

All packaging and protective materials removed (inside & outside of

appliance).

Media installed correctly.

Accessories installed properly.

Finishing (Pg

10 & 12

)

Verifi ed all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

Manual bag and all of its contents are removed from inside/

under the appliance and given to party responsible for use and operation.

Started appliance and veri

ed no

gas leaks exist.

Hearth & Home Technologies recommends the following:

STANDARD WORK CHECKLIST

Содержание AVFL Series













































Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды

Monessen Hearth AVFL Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды