Monessen Hearth AVFL Series Скачать руководство пользователя страница 2

Страница: 2 / 44

AVFL Vent Free Fireplace

Monessen • AVFL42NIP-SR Installation Instructions • 4119-900 Rev. B • 05/20

CONTENTS

Thank you and congratulations on your purchase of a Monessen fireplace.

PLEASE READ THE INSTALLATION AND OPERATION INSTRUCTIONS BEFORE USING THE APPLIANCE!

IMPORTANT: Read all instructions and warnings carefully before starting installation.

Failure to follow these instructions may result in a possible fire hazard and will void the warranty.

Standard Work Checklist

........................................... 3

Important Safety Information .................................... 4

Building Code Information

......................................... 5

Product Features

......................................................... 6

AVFL42 Controls

......................................................

Gas Specifications & Orifice Size .............................

Gas Pressures

..........................................................

Fireplace and Framing Dimensions

..........................

Pre-installation Information ........................................ 8

Getting Started

.........................................................

What You Will Need

..................................................

Planning the Installation

...........................................

Adequate Combustion and Ventilation Air

................

Fireplace Location

....................................................

Clearances & Height Requirements

.......................

Good Faith Guidelines for TV Installation

...............

Fireplace Installation ................................................. 12

Secure Fireplace to Framing

..................................

Finishing Material

...................................................

Noncombustible Facing Installation

........................

Connect the Gas

....................................................

Check Gas Pressure

..............................................

Electrical Installation................................................. 15

Wiring Junction Box ............................................... 15

Intellifire

™ Plus ODS Wiring Diagram

....................

Final Installation ........................................................ 17

Bulb Installation ......................................................

Installation of Air Deflection Glass ..........................

Glass Only Placement

............................................

Glass & Optional Stone Kit Placement

...................

Placement of Optional Logs

...................................

Operating Instructions .............................................. 21

For Your Safety Read Before Lighting ....................

Turning On Unit

......................................................

To Turn Off Gas to Appliance

..................................

Intellifire

™ Plus ODS System Operation ................. 23

Installation and Operating Instructions

...................

Maintenance and Cleaning

....................................... 31

Flame Appearance

.................................................

Check the Pilot Flame

............................................

Check Burner Flame Appearance ..........................

Cleaning and Servicing

..........................................

Replacing Light Bulbs .............................................

Operation and Optional Accessories

...................... 34

Operating Information

.............................................

Optional Accessories

..............................................

Troubleshooting

........................................................ 35

Intellifire

™ Plus ODS System

.................................

Service Parts .............................................................. 38

Limited Lifetime Warranty Policy

............................. 41

►

Содержание AVFL Series













































Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды

Monessen Hearth AVFL Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды