Monessen Hearth AVFL Series Скачать руководство пользователя страница 23

Страница: 23 / 44

AVFL Vent Free Fireplace

Monessen • AVFL42NIP-SR Installation Instructions • 4119-900 Rev. B • 05/20

IntelliFire™ Plus ODS

Initial Use

Initial Break-in Procedure
• The fireplace should run three to four hours continuously

on high.

• Turn the fireplace off and allow it to completely cool.
This cures the materials used to manufacture the fire

place.

NOTICE! Open windows for air circulation during

fireplace break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

NOTICE:

Some functionality will be lost when using

battery backup including remote control, lights, or any

other auxiliary functions that require household 110-120

VAC power.

Operation During A Power Outage

NOTICE:

Batteries should only be used as a power source

in the event of an emergency power outage. Batteries

should not be used as a primary long-term power source.

Figure 21 - Control Cavity Location

The IntelliFire™ Plus ODS intermittent pilot ignition system

comes with a battery backup system that enables the

system to operate in a power outage. The system offers

seamless transition from household AC power to battery

backup. A factory-installed battery pack is located in the

control cavity of the appliance. See Figure 21. Battery

longevity and performance will be affected by long term

exposure to the service temperatures of this appliance.

To Operate Fireplace Using Battery Power (DC):

1. Access the control cavity of the appliance. See Figure 21

for location. Lift the barrier screen off of the appliance.

2. Locate the battery tray and insert four AA cell batteries.

See Figure 21. Battery polarity must be correct or

module damage will occur.

A complete wiring diagram

is included in the electrical section of the appliance

installation manual.

3. Turn the appliance on according to the instructions

below for the appropriate type of control:

Standard Wall Switch or Factory-Installed ON/OFF

Switch:

• Toggle the switch as you would under normal

circumstances.

To Return to Operation Using Electrical (AC) Power
Standard Wall Switch or Factory-Installed ON/OFF

Switch:

• Toggle the switch to OFF.

• R

emove the batteries from the battery tray.

Wireless Remote:

• Slide the ON/REMOTE/OFF switch to the REMOTE

position.

• Remove the batteries from the battery tray.

Ignition Module:

• Slide the ON/REMOTE/OFF switch to the REMOTE

position.

• Remove the batteries from the battery tray.

Wireless Remote:

• Remote receiver is integrated into the ignition module

• Use the remote to turn the appliance on.
• To preserve battery life, do not use the HI/LO flame or

THERMOSTAT options.

Ignition Module:

• Locate the ignition module in the control cavity.
• Slide the ON/REMOTE/OFF switch to the ON position.

Burn Rate

The Artisan model has a variable burn rate which is con-

trolled by the remote control. Therefore the flame height

is adjustable.

The flame height may be adjusted as desired by locating

the flame option on the remote control and adjusting up or

down to desired flame height.

Gas Valve

Control Module

Battery Tray

Содержание AVFL Series













































Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды

Monessen Hearth AVFL Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды