Monessen Hearth AVFL Series Скачать руководство пользователя страница 12

Страница: 12 / 44

AVFL Vent Free Fireplace

Monessen • AVFL42NIP-SR Installation Instructions • 4119-900 Rev. B • 05/20

FIREPLACE INSTALLATION

SECURE FIREPLACE TO FRAMING

The fireplace must be secured to the framing studs as

shown in

Figure 6.

Use eight (8) screws to attach fireplace

to framing. The side nailing flanges are

⁄

" or

⁄

" to accom-

modate different wall thickness.

NOTE

Never install combustible materials over

front face of fireplace.

FINISHING MATERIAL

NOTE:

Any remote wiring (i.e. remote control, wall

switch), must be done prior to final finishing to avoid costly

reconstruction.
Only noncombustible materials (i.e. brick, tile, slate, steel,

or other materials with a UL fire rating of Zero) may be

used to cover the black painted face of the appliance. It is

permissible to bring combustible wall board to the top of

the standoffs on the top and to the wall board stand-offs

on the sides of the unit. A 300°F minimum adhesive may

be used to attach facing materials to the black surface. If

joints between the finished wall and the fireplace surround

are sealed, a 300°F minimum sealant material (General

Electric RTV103 or equivalent) must be used.

NOTE:

Fireplace may be installed on top of framing or

platform constructed of combustible materials which do

not protrude beyond the face.

NONCOMBUSTIBLE FACING INSTALLATION

CAUTION

: The noncombustible wall board supplied with

this unit can be damaged if dropped or struck. Handle

with care.

1. Using drywall screws secure noncombustible board to

the two brackets on top of unit.

IMPORTANT

: To avoid

cracking the board, pre-drill holes prior to securing to the

unit/framing.

2. Wipe any debris or dust from the noncombustible board

and drywall.

3. It is highly recommended to prime the facing using a

quality primer prior to taping and mudding. This will

ensure proper adhesion of both the tape and mud. The

supplied board is very porous.

4. Tape the seams using a mesh type tape.

5. Mud seams as normal. We recommend using a product

called Durabond high strength compound for the first

coat. This product can be purchased at any hardware

store. Follow manufacturer's recommendations for curing

the mud. NOTE: Depending upon the final finishing

method, use a minimum rated 300 degree sealant, dry

wall compound or thin set to seal the side and top joints.

6. Prime wall for a second time for proper adhesion of paint.

43"

44"

32"

MOUNTING POINTS

FP3009

Framing

Members

Nailing

Flange

Screws

Noncombustible Material

FP3009
secure fireplace

5”

Nailing

Flange

Nailing

Flange

Screws

Noncombustible board

Figure 6 –

Secure Fireplace to Framing Studs

Figure 6A –

Noncombustible facing installation

Содержание AVFL Series













































Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды

Monessen Hearth AVFL Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды