Monessen Hearth AVFL Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 44

background image

18

AVFL Vent Free Fireplace

Monessen • AVFL42NIP-SR Installation Instructions • 4119-900 Rev. B • 05/20

6. Remove five screws that secure the rear hearth in

place and remove from unit.

Figure 13

7. Figure 14 shows bulb placement for front and rear

light bars. Insert bulbs in sockets.

8. With (twelve 15W) bulbs installed in front and rear

light bar, reinstall the rear hearth first with five
screws that were removed earlier.

Figure 13

9. Reinstall the front hearth with nine screws removed

earlier.

Figure 13

10. Place the rear porcelain panel back in place and

reinstall the left and right side using same screws

that were removed earlier.

11. Re-install the air deflection glass before proceeding

to add decorative media (next page).

FINAL INSTALLATION

Nine Front Hearth Screws

Five Rear Hearth Screws

Front Lower Light Bulbs

Rear Lower Light Bulbs

Figure 13–

Hearth Screw Locations

Figure 14–

Lower Light Bulb Location

«
...
16
17
18
19
20
...
»

Содержание AVFL Series













































Отзывы:

Нет отзывов

Похожие инструкции для AVFL Series

Бренд: Majestic Страницы: 40

Бренд: NovaFlex Страницы: 24

mantels & surrounds Kenwood Flush

Бренд: Fireside Страницы: 6

ChimneyFree 25MM5326

Бренд: Twin-Star International Страницы: 24

Бренд: Evonicfires Страницы: 29

Fire Ribbon Direct VEnt Slim 26"

Бренд: Spark Страницы: 48

Бренд: Paramount Fitness Страницы: 44

Бренд: HAMPTON BAY Страницы: 9

Бренд: HAMPTON BAY Страницы: 9

Бренд: Lopi Страницы: 40

Бренд: Lopi Страницы: 15

864 TRV 31K CleanFace

Бренд: Lopi Страницы: 60

Бренд: Klarstein Страницы: 36

Бренд: Klarstein Страницы: 44

Бренд: Klarstein Страницы: 64

Бренд: Klarstein Страницы: 64

Бренд: Klarstein Страницы: 21

Бренд: Megamaster Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды