Monessen Hearth AVFL Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 44

background image

17

AVFL Vent Free Fireplace

Monessen • AVFL42NIP-SR Installation Instructions • 4119-900 Rev. B • 05/20

FINAL INSTALLATION

BULB INSTALLATION

NOTE

: This unit is shipped without bulbs installed to pre-

vent any damage to the bulb filament during transport.
This unit is shipped with a total of 13 bulbs (twelve 15W
bulbs and one 90W bulb). These instructions apply to
new installations only. If replacing bulbs after the installa

-

tion is complete, see page 32 for instructions.

LOWER LIGHT BAR BULB INSTALLATION

1. Remove air deflection glass from the unit and place

on a flat, clean surface.

2. Using a Phillips screwdriver remove the screws (one

each) holding the left and right porcelain panels in

place.

3. Carefully remove the panels from the unit plac

-

ing them on a clean level surface.

NOTE:

The rear

porcelain panel is held in place by the left and right
panel and could fall forward if not supported during

removal of the side panels.

CAUTION

Turn OFF the main power supply before perform-

ing any service work on the unit, including install

-

ing or replacing light bulbs.

TOP LIGHT BULB INSTALLATION

1. Remove three screws holding light cover in place

(as shown in Figure 11)

2. Insert (1) 90W bulb provided into socket
3. Replace top light cover with three screws

4. With side panels removed the rear porcelain panel

can be removed from the unit and placed on a clean,
level surface.

5. Remove nine screws that secure the front hearth in

place and remove from unit.

Figure 13

Top light

location

Porcelain

panel screw

Porcelain

panel screw

Light cover

screws

Figure 10–

Top Light Position; Porcelain Panel Screw Location

Figure 11–

Top Light Screws

Figure 12–

Porcelain Panel Screw Location

«
...
15
16
17
18
19
...
»

Содержание AVFL Series













































Отзывы:

Нет отзывов

Похожие инструкции для AVFL Series

Бренд: Valor Страницы: 12

Бренд: barbas Страницы: 100

Бренд: Calflame Страницы: 32

Бренд: HAMPTON BAY Страницы: 40

Бренд: Napoleon Страницы: 8

Luna Gold Series

Бренд: M Design Страницы: 14

FALLSTON 1006152671

Бренд: Home Decorators Collection Страницы: 21

Бренд: Focus Страницы: 36

Бренд: HEINZE Страницы: 2

Бренд: Wonderfire Страницы: 22

Бренд: Wonderfire Страницы: 29

Бренд: Sunjoy Страницы: 4

CASUAL FIRESIDE 5110-2875O

Бренд: OW Lee Страницы: 28

CASUAL FIRESIDE 5110-2442O-E

Бренд: OW Lee Страницы: 28

Бренд: OW Lee Страницы: 28

Бренд: Empire Comfort Systems Страницы: 20

Бренд: Empire Comfort Systems Страницы: 12

Бренд: Empire Comfort Systems Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды