Monessen Hearth AVFL Series Скачать руководство пользователя страница 10

Страница: 10 / 44

AVFL Vent Free Fireplace

Monessen • AVFL42NIP-SR Installation Instructions • 4119-900 Rev. B • 05/20

PRE-INSTALLATION INFORMATION

CLEARANCES AND HEIGHT REQUIREMENTS

Ensure that minimum clearances shown in

Figures 4 and

are maintained. Left and right clearances are determined

when facing the front of the firebox.

Follow these instructions carefully to ensure safe instal-

lation. Failure to follow these requirements may create a

fire hazard.

Sidewall & Mantel Leg Clearances

— The clearance from

the inside of the appliance to any combustible adjacent

wall should not be less than 6". Mantel leg clearances are

projected out at a 45° angle.

Figure 5

Ceiling Clearance

— The ceiling must be at least 36" from

the firebox opening.

Figure 5

Back Wall Clearance

— The appliance may be placed

against a combustible back wall.

ARNING

The dimensions shown in

Figures 4 and

are minimum clearances to maintain

when installing this heater. Left and right

clearances are determined when facing the

front of the heater.
Follow these instructions carefully to

ensure safe installation. Failure to follow

instructions exactly can create a fire hazard.

Floor Clearance

— The fireplace may be installed directly

on a combustible floor or a raised platform of an appropriate

height. Do not place fireplace on carpeting, vinyl, tile or

other soft floor coverings. It may, however, be placed on flat

wood, plywood, particle board or other hard surfaces. Be

sure fireplace rests on a solid continuous floor or platform

with appropriate framing for support so that no cold air can

enter from under the firebox. See note below regarding

floor installation with wide contemporary faces.

Mantel clearances

— Must meet the clearance require-

ments detailed in

Figure 5.

This is for combustible and

non-combustible mantels.

Eyebrow

Screws

Eyebrow must be installed with the three (3) screws

provided.

Figure 4

Figure 4 –

Eyebrow Installation

Figure 5 –

Sidewall, Mantel Leg and Ceiling Clearances

14"

18"

12"

FP3007

mantel clearances

36"

Top of Fireplace

Opening

SIDE VIEW

Wall

Insulation

Board

Stud

Standoff

¹⁄₂

45°

¹⁄₂

FP3008

mantel leg

¹⁄₂

Fireplace

Opening

TOP VIEW

Ceiling

Sidewall

Содержание AVFL Series













































Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды

Monessen Hearth AVFL Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды