Monessen Hearth AVFL Series Скачать руководство пользователя страница 28

Страница: 28 / 44

AVFL Vent Free Fireplace

Monessen • AVFL42NIP-SR Installation Instructions • 4119-900 Rev. B • 05/20

IntelliFire™ Plus ODS

About ON Mode

• All functions can be accessed when the remote control

is in the ON mode.

• Only active functions will be displayed when the remote

control is in the ON mode.

About OFF Mode

Only the following functions can be accessed in the OFF

mode:

• AUX1-Lower Light Bar
• AUX2-Top Dome Light

Only active functions will be displayed when the remote

control is in the OFF mode.

Turning On the Fireplace

• Press the POWER button to turn the fireplace ON. The

fireplace will first ignite the pilot. Once the pilot flame is

established the main burner will be lit.

NOTICE:

Whenever the fireplace is cycled from OFF to

ON, the main burner will light on high for 10 seconds before

returning to the previous user setting.

Adjusting Flame Height

• Press the

MENU

button to activate the menu.

• Using the

and

DOWN

arrows highlight the

FLAME

icon and press

SELECT

• Use the

and

DOWN

arrows to adjust the

FLAME

HEIGHT

, then press

SELECT

. The

FLAME HEIGHT

can be adjusted to 5 different settings.

NOTICE:

FLAME HEIGHT will not be adjustable for first

ten seconds when fireplace is turned on.

NOTICE:

The system will remember the previous FLAME

HEIGHT setting and will automatically adjust after 10

seconds.

NOTICE:

Some models use fixed valves, which cannot

be adjusted.

AUX1 Function (Lower Light Bar)
AUX2 Function (Top Dome Light)

• Press the

MENU

button to activate the menu.

• Using the

and

DOWN

arrows highlight the

AUX1

icon

and press

SELECT

• Use the

and

DOWN

arrows to adjust the

AUX1

output,

then press

SELECT

. The

AUX1

function

can be adjusted

to 4 different settings: HI, MED, LOW and OFF.

Adjusting Thermostat

• Press the

MENU

button to activate the menu.

• Using the

and

DOWN

arrows highlight the

THERMO

icon and press

SELECT

• Use the

and

DOWN

arrows to turn the

THERMO

OFF

, then press

SELECT

(the

SET TEMP

will start

blinking). Using the

and

DOWN

arrows select the

desired temperature and press

SELECT

NOTICE:

If the THERMO function is on, the SET TEMP

can be adjusted at any time by pressing the UP and DOWN

arrows.

NOTICE:

As the ROOM TEMP (RT) approaches SET

TEMP (ST), the remote system will automatically adjust

the flame height. If the RT rises above ST, the fireplace

will shut down the main burner. After this, the fireplace will

turn back on after the RT drops below the ST.

NOTICE:

The system requires a two degree Fahrenheit

or higher temperature difference between RT and ST for

the fireplace to turn on.

NOTICE:

The system will remember the previous TEM-

PERATURE setting when THERMOSTAT mode is cycled

ON or OFF.

NOTICE:

If your installation includes an optional wired ON/

OFF wall switch, it should be in the OFF position when

using the RC300 in thermostat mode.

Adjusting Timer

• Press the

MENU

button to activate the menu.

• Using the

and

DOWN

arrows highlight the

TIMER

icon and press

SELECT

• Use the

and

DOWN

arrows to turn the

TIMER

OFF

, then press

SELECT

. Using the

and

DOWN

arrows select the desired set time and press

SELECT

Timer operates in increments of 15, 30, 45, 60, 90, 120

and 180 minutes.

Setting the Child Lock

• Press and hold the

MENU

and

arrow buttons simul-

taneously for 4 seconds to enable or disable the child

lock feature.

NOTICE:

No functions will be usable until child lock feature

is disabled.

Содержание AVFL Series













































Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды

Monessen Hearth AVFL Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AVFL Series

Отзывы:

Похожие инструкции для AVFL Series

Бренды по названию

Популярные бренды