7
Note:
The number of available fan speeds depends on the type of unit connected.
Note also that some units do not provide an “Auto” setting.
In the following cases, the actual fan speed generated by the unit will differ
from the speed shown the remote controller display.
1. While the display is showing “STAND BY” or “DEFROST”.
2. When the temperature of the heat exchanger is low in the heating mode.
HJLPPHGLDWHO\DIWHUKHDWLQJRSHUDWLRQVWDUWV
3. In HEAT mode, when room temperature is higher than the temperature
setting.
:KHQWKHXQLWLVLQ'5<PRGH
5.2. Mode select
Press the operation mode (
) button
and select the op-
eration mode
.
Cooling mode
Drying mode
Fan mode
Heating mode
Automatic (cooling/heating) mode
Automatic operation
According to a set temperature, cooling operation starts if the room
temperature is too hot and heating operation starts if the room tem-
perature is too cold.
During automatic operation, if the room temperature changes and
remains 1.5°C, 3°F or more above the set temperature for 3 minutes,
the air conditioner switches to cooling mode. In the same way, if the
room temperature remains 1.5°C, 3°F or more below the set tempera-
ture for 3 minutes, the air conditioner switches to heating mode.
5. Operation
Cooling mode
3 minutes (switches from
heating to cooling)
Set tempe1.5°C, +3°F
Set temperature
Set temperature -1.5°C, -3°F
3 minutes (switches from cool-
ing to heating )
Because the room temperature is automatically adjusted in order to
PDLQWDLQD¿[HGHIIHFWLYHWHPSHUDWXUHFRROLQJRSHUDWLRQLVSHUIRUPHG
a few degrees warmer and heating operation is performed a few de-
grees cooler than the set room temperature once the temperature is
reached (automatic energy-saving operation).
5.3. Temperature setting
To decrease the room temperature:
Press
button
to set the desired temperature.
The selected temperature is displayed at
.
To increase the room temperature:
Press
button
to set the desired temperature.
The selected temperature is displayed at
.
• Available temperature ranges are as follows:
Cooling/Drying:
19 - 30°C, 67 - 87 °F
Heating:
17 - 28°C, 63 - 83 °F
Automatic:
19 - 28°C, 67 - 83 °F
• The display blinks either 8°C - 39°C, 46°F - 102°F to inform you if the
room temperature is lower or higher than the displayed temperature.
)DQVSHHGVHWWLQJ
Press the Fan Speed button
as many times as necessary while the
system is running.
• Each press changes the force. The currently selected speed is
shown at
.
• The change sequence, and the available settings are as follows.
FAN SPEED
Display
4-speed
+
Auto *
3-speed
+
Auto *
4-speed
model
Speed 1
Speed 2 Speed 3 Speed 4
Speed 1
Speed 2
Speed 3
Speed 4
Auto
Ŷ
$XWRPDWLFIDQVSHHGVHWWLQJ)RUZLUHOHVVUHPRWHFRQWUROOHU
It is necessary to set for wireless remote controller only when
automatic fan speed is not set at default setting.
It is not necessary to set for wired remote controller with automatic
fan speed at default setting.
Press the SET button with something sharp at the end.
Operate when display of remote controller is off.
MODEL SELECT
blinks and Model No. is lighted
.
Press the AUTO STOP
button.
blinks and setting No. is lighted
.
(Setting No.01: without automatic fan speed )
Press the temp.
buttons to set the setting No.02.
(Setting No.02:with automatic fan speed )
If you mistook the operation, press the ON/OFF
button and oper-
ate again from procedure
.
Press the SET button with something sharp at the end.
MODEL SELECT
and Model No. are lighted for 3 seconds, then turned off.
ON/OFF
TEMP
RESET
SET
CLOCK
MODEL SELECT
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
$LUÀRZGLUHFWLRQVHWWLQJ
7R&KDQJHWKH$LUÀRZ¶V8S'RZQ'LUHFWLRQ!
:LWKWKHXQLWUXQQLQJSUHVVWKH$LUÀRZ8S'RZQEXWWRQ
as neces-
sary.
• Each press changes the direction. The current direction is shown at
.
• The change sequence, and the available settings, are as follows.
* Note that during swing operation, the directional indication on the
screen does not change in sync with the directional vanes on the unit.
* Some models do not support directional settings.
*1. For MA remote controller only, other remote controllers display the
same as 4 steps model.
*2. PKFY-P·NBMU-E2 has no swing display.
$LUÀRZGLUHFWLRQVHWWLQJ$XWR!
COOL / FAN / DRY: Setting 1 (Horizontal), HEAT: Setting 5 (Downward 5)
$LUÀRZ
Display
5 steps
model*1
4 steps
model
1
2
3
4
(Horiz.)
Swing
Swing
Auto
1
2
3
4
5
* For MA remote controller only.
Automatic fan speed setting is necessary for wireless remote controller.
Speed 1
Speed 2
Speed 3
Auto
