Mitsubishi MOTORS Lancer 2005 Скачать руководство пользователя страница 103

Страница: 103 / 109

MPI <4G63>

On-vehicle Service

13D-98

ENGINE COOLANT TEMPERATURE SENSOR
CHECK

Caution
Be careful not to touch the connector (resin section) with
the tool when removing and installing.

Remove the engine coolant temperature sensor.

With temperature sensing portion of engine coolant
temperature sensor immersed in hot water, check
resistance.

Standard value:

17 k

(at

5.1

6.5 k

(at 0

2.1

2.7 k

(at 20

0.9

1.3 k

(at 40

0.48

0.68 k

(at 60

0.26

0.36 k

(at 80

If the resistance deviates from the standard value greatly,
replace the sensor.

Apply sealant to threaded portion.

Specified sealant:

3M NUT Locking Part No. 4171 or equivalent

Install the engine coolant temperature sensor and tighten
it to the specified torque.

Tightening torque: 29

10 N·m

THROTTLE POSITION SENSOR CHECK

Disconnect the throttle position sensor connector.

Measure the resistance between the throttle position
sensor side connector terminal No. 1 and terminal No.
4.

Standard value: 3.5

6.5 k

Measure the resistance between the throttle position
sensor side connector terminal No. 2 and terminal No.
4.

Normal condition:

Throttle valve slowly open
until fully open from the idle
position

Changes smoothly in
proportion to the opening
angle of the throttle valve

If the resistance is outside the standard value, or if it
doesn’t change smoothly, replace the throttle position
sensor.

NOTE
For the throttle position sensor adjustment procedure,
refer to P.13D-90.

Engine coolant
temperature sensor

Equipment side connector

Throttle position sensor

Equipment side connector

Содержание Lancer 2005














































































































Результаты поиска

Содержание Lancer 2005

Отзывы:

Похожие инструкции для Lancer 2005

Бренды по названию

Популярные бренды

Mitsubishi MOTORS Lancer 2005, Дополнение к руководству по ремонту

Результаты поиска

Содержание Lancer 2005

Отзывы:

Похожие инструкции для Lancer 2005

Бренды по названию

Популярные бренды