Mitsubishi MOTORS Lancer 2005 Скачать руководство пользователя страница 52

Страница: 52 / 109

MPI <4G63>

Troubleshooting

13D-47

INSPECTION PROCEDURE 11

When the engine is cold, it stalls at idling. (Die out)

Probable cause

In such cases as the above, the cause is probablythatthe air/fuelmixture is inappropriate
when the engine is cold, or that the intake air volume is insufficient.

Malfunction of the ISC servo system

Malfunction of the throttle body

Malfunction of the injector system

Malfunction of the ignition system

Were the battery terminals disconnected?

YES

After warming-up, let the engine run at idling for 10 minutes.

M.U.T.-

II/III

Self-Diag code

Are diagnosis codes displayed?

YES

Refer to P.13D-12, INSPECTION CHART FOR DIAGNOSIS
CODES.

Does the engine stall right after the accelerator pedal is released?

YES

Clean the throttle valve area. (Refer to P.13D-90.)

Is engine-idling stable after the warming-up?

Check if the unstable idling (Rough idling, hunting).
(Refer to P.13D-44, INSPECTION PROCEDURE 8.)

YES

Check the ISC servo for operation sound. (Refer to P.13D-102.)

Check the ISC servo system.
(Refer to P.13D-64, INSPECTION PROCEDURE 32.)

Check the injector for operation sound.

Check the injector system. (Refer to P.13D-29, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)

M.U.T.-

II/III

Data list

14 Throttle position sensor (Refer to P.13D-66.)

Check the throttle position sensor system. (Refer to P.13D-18,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 14.)

M.U.T.-

II/III

Data list

21 Engine coolant temperature sensor (Refer to P.13D-66.)

Check the engine coolant temperature sensor system.
(RefertoP.13D-20,INSPECTION PROCEDUREFORDIAGNOSIS
CODE 21.)

Check the fuel pressure. (Refer to P.13D-92.)

Check the ignition timing.
(Refer to GROUP 11C

On-vehicle Service.)

Check that the crank angle sensor is installed properly.

Check the following items.

Check the ignition coil, spark plugs, spark plug cables.

Check the compression pressure.

Check the engine oil viscosity.

M.U.T.-

II/III

Actuator test

10 EGR control solenoid valve (Refer to P.13D-70.)

Check the EGR control solenoid valve system.
(Refer to P.13D-65, INSPECTION PROCEDURE 34.)

Содержание Lancer 2005














































































































Результаты поиска

Содержание Lancer 2005

Отзывы:

Похожие инструкции для Lancer 2005

Бренды по названию

Популярные бренды

Mitsubishi MOTORS Lancer 2005, Дополнение к руководству по ремонту

Результаты поиска

Содержание Lancer 2005

Отзывы:

Похожие инструкции для Lancer 2005

Бренды по названию

Популярные бренды