Mitsubishi Heavy Industries FDCR224KXE6, Техническое руководство

Страница: 87 / 157

- 85 -
'11 • KX-T-166
Code
No.
Write contents
Record data
Data write range Unit of write
Number of
bytes
Contents
0 Error code 00 ~ 99 – 1
00: No error on outdoor unit
01-99: All errors
1 Error existing unit address 00 ~ FF – 1
00 – 3F: Outdoor
40 – 6F: Indoor
<Sensor value>
2 Tho-A Outdoor air temperature -20 ~ 70 A/D value 1
3 Tho-R1 Heat exchanger temp. 1 -40 ~ 75 A/D value 2
4 Tho-R2 Heat exchanger temp. 2 -40 ~ 75 A/D value 2
5 Tho-D1 Discharge pipe temp. (CM1) -20 ~ 140 A/D value 1
6 Tho-S Suction pipe temperature -40 ~ 75 A/D value 2
7 Tho-SC Sub-cooling coil temp. 1 -40 ~ 75 A/D value 2
8 Tho-H Sub-cooling coil temp. 2 -40 ~ 75 A/D value 2
9 Tho-P1 Power transistor temp. (Radiator fin) -20 ~ 140 A/D value 1
10 Inverter secondary current 0 ~ 50 A/D value 1
11 Tho-C1 Under-dome temp. (CM1) -40 ~ 90 A/D value 1
12 CT1 Current 0 ~ 50 A/D value 1
13 High pressure sensor 0 ~ 4.15 A/D value 1
14 Low pressure sensor 0 ~1.70 A/D value 1
<Outdoor unit information>
15 Number of connected indoor units 0 ~ 127 1 unit 1
16 Capacity of connected indoor units 0 ~ 65535 – 2
17 Number of indoor units with thermostat ON 0 ~ 255 1 unit 1
18 Total capacity of indoor units with cooling
thermostat ON
0 ~ 65535 2
19 Total capacity of indoor units with heating
thermostat ON
0 ~ 65535 2
20 Operation mode 0 ~ 2 – 1
0 Stop
1 Cooling
2 Heating
21 Inverter CM1 actual operation frequency 0 ~ 255 1Hz 1
22 FMo1 Actual fan speed 0 ~ 65535 10min-1 2
23 FMo2 Actual fan speed 0 ~ 65535 10min-1 2
24 Required Hz total 0 ~ 65535 1Hz 2
25 Discharge pressure saturated temperature -50 ~ 70 0.01°C 2
26 Suction pressure saturated temperature -50 ~ 30 0.01°C 2
27 Sub-cooling coil temp. sensor 1 saturated
pressure
-0.68 ~ 4.15 0.01MPa 2
28 Pressure ratio 1.0 ~ 10.0 0.1 1 See below
※
mark
29 Cooling sub-cooling 0 ~ 50 0.1deg 2
30 Suction overheat 0 ~ 50 0.1deg 2
31 Sub-cooling coil overheat 0 ~ 50 0.1deg 2
32 Discharge pipe overheat 0 ~ 50 0.1deg 2
33 Compressor 1 under-dome overheat 0 ~ 50 0.1deg 2
34 Target Fk 0 ~ 65535 1Hz 2
35 Answer Hz total
※ Definition of signals
No.28: Pressure ratio
Pressure ratio = (High pressure 0.101) [MPa] / (Low pressure 0.101) [MPa]
0 ~ 65535 1Hz 2
36 Inverter 1 operation frequency command 0 ~ 120 1Hz 1