Mitsubishi Electric Mr.Slim MUZ-GC25NA - C1 Скачать руководство пользователя

Страница: 37 / 64

B Check of open phase

MUZ-GC25/35NA MUZ-GC50NA-

●

With the connector between the compressor and the intelligent power module disconnected, activate the inverter and check if

the inverter is normal by measuring the balance of voltage between the terminals.

Output voltage is 50 - 130 V. (The voltage may differ according to the tester.)

<< Operation method>>

Start cooling or heating operation by pressing EMERGENCY OPERATION switch on the indoor unit. (TEST RUN OPERA-

TION : Refer to 6-3.)

<<Measurement point>>

At 3 points

BLK (U)-WHT (V)

BLK (U)-RED (W)

WHT(V)-RED (W)

NOTE

: 1. Output voltage varies according to power supply voltage.

2. Measure the voltage by analog type tester.

3. During this check, LED of inverter P.C. board

ashes 9 times. (Refer to 9-6.1.)

Measure AC voltage between the

lead wires at 3 points.

C Check of compressor

MUZ-GC25/35NA MUZ-GC50NA-

Refer to 9-5. “Check of compressor

operation time”. Does the compressor

operate continuously?

OK.

Yes

Refer to 9-5. “Check of compressor

winding”. Is the compressor normal?

Replace the compressor.

Yes

Refer to 9-5. "Check of compressor start failure".

MUZ-GC25/35NA

●

Disconnect the connector (CN61) between the compressor and intelligent power module, and measure the resistance be-

tween the compressor terminals.

<<Measurement point>>

At 3 points

BLK-WHT

BLK-RED

WHT-RED

<<Judgement>>

Refer to 9-4.

] ················Abnormal [short]

Infinite[

] ·······Abnormal [open]

NOTE

: Be sure to zero the ohmmeter before measurement.

Measure the resistance between the lead wires at 3 points.

D Check of compressor winding

Содержание Mr.Slim MUZ-GC25NA - C1

































































Результаты поиска

Содержание Mr.Slim MUZ-GC25NA - C1

Отзывы:

Похожие инструкции для Mr.Slim MUZ-GC25NA - C1

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim MUZ-GC25NA - C1, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim MUZ-GC25NA - C1

Отзывы:

Похожие инструкции для Mr.Slim MUZ-GC25NA - C1

Бренды по названию

Популярные бренды