Mitsubishi Electric Mr.Slim MUZ-GC25NA - C1 Скачать руководство пользователя

Страница: 42 / 64

J Check of power supply

MUZ-GC25/35NA MUZ-GC50NA-

Is there voltage 220 - 230 VAC

between the indoor terminal

block S1 and S2?

Yes

Replace the indoor

electronic control P.C.

board.

Rectify indoor/outdoor

connecting wire.

Yes

If light up, OK.

ash, refer to 9-3.

Does the upper or left lamp of

OPERATION INDICATOR lamp on

the indoor unit light up?

Dose LED on the inverter P.C.

board light up or

ash? (Refer

to 9-6.1.)

Replace the inverter

P.C. board.

Is there voltage 280 - 370 VDC

between DB61 (+) and DB61 (–) on

the inverter P.C. board?

(Refer to 9-6.1.)

Check the electric parts in main circuit.

Yes

Disconnect the connector (CN61)

between compressor and intelligent

power module.

Turn ON power supply and press

EMERGENCY OPERATION switch.

Inverter P.C. board

(Solder side)

DB61

280 - 370 VDC

Is there voltage of 220 - 230 VAC in the

power supply terminal block?

Check the connecting of parts of main power

supply circuit.

Check the power supply cable.

Turn ON power supply.

Is the output voltage from the noise

lter P.C.

board 220 - 230 VAC?

Replace the noise

lter

P.C. board.

Yes

Is the input voltage to the power board 220 -

230 VAC?

Replace the reactor.

Yes

Is the input voltage to the outdoor electronic

control P.C. board 325 VDC?

Replace the power board.

Replace the outdoor electronic control P.C. board.

Yes

Is fuse (F64) blown?

Yes

Replace the fuse.

MUZ-GC50NA-

MUZ-GC60/71NA

Содержание Mr.Slim MUZ-GC25NA - C1

































































Результаты поиска

Содержание Mr.Slim MUZ-GC25NA - C1

Отзывы:

Похожие инструкции для Mr.Slim MUZ-GC25NA - C1

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim MUZ-GC25NA - C1, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim MUZ-GC25NA - C1

Отзывы:

Похожие инструкции для Mr.Slim MUZ-GC25NA - C1

Бренды по названию

Популярные бренды