MIMAKI CJV30 Series, Руководство по обслуживанию

Страница: 5 / 316

© 2009 MIMAKI ENGINEERING CO.,LTD. Maintenance Manual Change Tracking P.4
Service Documents > Maintenance Manual Change Tracking
Maintenance Manual Change Tracking
3.1.2 Revised 1.10 Work operation 1: “station cover U and ...”

“station cover U, W ink guard and ...”
Revised 1.10 Work operation 3: “... while it is pressed against the innermost part.”

“... while pushing it toward you.”
3.1.3 Revised 1.10 Work operation 1: “Remove the ICU cover F, ICU cover R, ...”

“Remove the ICU cover, ...”
3.1.4 Revised 1.10 Section changed: “3.3. Driving Parts”

“3.1. Ink Related Parts”
Revised 1.10 Work operation 1: “... C station cover.”

“... C station cover 2.”
3.2.1 Added 1.10 Work operation 4: “In installation, pay attention to harness treatment.”
Revised 1.10 Work operation 7: “7.0 mm”

“8.8 mm”
1.10 Work operation 8 to 10: The order of work items changed and items added
3.2.2 Revised 1.10 Work operation 1: “... auto cutter assy.”

“... S guide.”
1.10 Work operation 4: “7.0 mm”

“8.8 mm”
Added 1.10 Work operation 4: “(If necessary, check to see if the magnet catcher...”
1.10 Work operation 6: “Install the S guide while pushing it to the left.”
Erased 1.10 Caution Box: “Be sure to wear protective glasses and working gloves...”
3.2.3 Added 1.10 Work operation 4: “Set the pressure of all the clamps to Middle,...”
Revised 1.10 Work operation 6: “Adjust the pen stroke at...”

“Adjust so that the pen stroke is...”
1.10 Work operation 7: “7.0 mm”

“8.8 mm”
Added 1.10 Work operation 11, 12
1.10 Important Box: “Once the S guide is removed, ...”
3.3.2 Added 1.10 Work operation 1: “...and D BKT cover.”
3.3.3 Erased 1.10 Work operation 4: “Greasing of Y drive belt”
3.3.5 Added 1.10 Work operation 5: “GR/PR adjustment”
1.10 Work operation 6: “Install all the covers temporarily first ...”
3.4.1 Revised 1.10 Work operation 3/4: “Mounting” / “Removal”
Erased 1.10 Caution Box: “Be sure to wear protective glasses and working gloves...”
4.1.1 Erased 1.10 Adjustment item:Adjustment of light pointer offset
Adjustment of cutting position
Work contents: Pulley BTG removal or replacement
Paper sensor
4.2.2 Added 1.10 Tips Box: “The same adjusted value is applied to...”
4.2.3 Added 1.10 Important Box: “Make adjustment with [EXPANDS] of...”
Erased 1.10 Tips Box: “If the unit is changed to inch,...”
4.2.5 Revised 1.10 Adjustment procedure 4: “Vertically shifts the cap.”

“Shifts the cap.”
1.10 Adjustment procedure 5: “Horizontally shifts the head.”

“Horizontally shifts the wiper.”
4.2.8 Page deleted – “Remarks” and “Examples of inputting a compensation value”
4.2.9 Revised 1.10 Function: “400g”

“350g”
Procedure 6: “400g”

“350g”
4.2.10 Revised 1.10 Function: “Plots 11 square patterns using the 11 pen landing values of 0 to 200, respectively. (20 steps)”

“Plots 11 square patterns at the positions of different pen landing values in steps of 20, start-
ing at the first pen landing point.”
Added 1.10 Function (The content of adjustment...): “#LANDING UP POSITION”
Added 1.10 Procedure 3 to 6: Because of addition of “#LANDING UP POSITION”
Revised 1.10 Procedure 7: “... the 11 pen landing values (0, 20, 40 ... 200) of 0 to 200 currently being set.”

”... different pen landing values in steps of 20, starting with the currently set pen landing value.”
Date 2008.09.17 Manual Ver. 1.10 Remark
Index Status Rev. Changes