MIMAKI CJV30 Series, Руководство по обслуживанию

Страница: 261 / 316

© 2009 MIMAKI ENGINEERING CO.,LTD. 7.1.3 P.2
7.1.3 List of Warning Messages
1
2
3
4
5
6
7
8
 List of Warning Messages (2/3)
No. Indication on LCD Cause Remedy
18 <LOCAL.1> !CAR [#01]
INK REMAIN K-------
The ink of the 600cc package has been
completely used up.
Reset the cartridge and set the amount of remaining ink. If the
ink that can be used is remaining, the warning is cancelled
and the cartridge can be used continuously. If the ink that can
be used is not remaining,the warning is not cancelled.
19
<LOCAL.1> !CAR [#01]
REINSERT CARTRIDGE
End sensor is detected with enough ink
remaining
Reinstall appropriate cartridge
Check or replace the end sensor if it is detected after reinstal-
lation
20
<LOCAL.1> !CAR [#01]
!WASTE TANK
The waste ink tank is nealy full.
(The waste ink count has reaced the spec-
ified value.)
Reinstall appropriate cartridge
Check or replace the end sensor if it is detected after reinstal-
lation
21
<LOCAL.1> !CAR [#01]
!Wash Liquid END
Emptied washing liquid cartridge was
detected.
Replace the maintenance washing liquid cartridge with a new
one. If the problem still cannot be solved, check the follow-
ings.
1. Check that the cartridge end sensor works properly with
[#TEST] -> [WASH CARTRIDGE].
2. If it does not work properly, replace the sensor or IO
PCB assy with a new one.
22 <LOCAL.1> !CAR [#01]
!WashLiquidCart.NONE
The washing liquid cartridge has not been
installed.
23 <LOCAL.1> !CAR [#01]
!WRONG WASH CART.
Trouble with washing liquid cartridge has
been detected.
(Ex.Ink cartridge is set)
Install the maintenance washing liquid cartridge.
24

Washing liquid


un-filling up.

Maintenance washing liquid has not been
supplied.
Supply the maintenance washing liquid.
(Execute [MAINTENANCE] -> [HD.MAINTENANCE] ->
[FILL UP INK].)
25

OFFSCALE

The cutting data exceeds the effective
cutting area.
Or the machine has stopped after cutting
the media up to its end normally.
Use a larger size of media, decrease the amount of data or
execute the divided cutting function.
26

END COPY

The machine has terminated copying
after completion of one sheet copying,
since the data received contains the origin
updating command.
The cutting of two or more sheets is not allowed.
To have the machine cut two or more sheets, change the set-
ting on the host computer beforehand.
27

DIVISION

5s
The machine has finished the cutting cor-
responding to a division of the data that
exceeds the media width, using the divi-
sion cut function, and is now waiting for
the receipt of the next data.
When the machine does not receive any data from the host
computer within ten seconds, it will recognize the data has
ended.
Then the machine will perform the frame cutting and mark
cutting and return to local mode.
28

END DIVISION

Displayed in any of the following cases:
•Media width is 1 cm or less.
•Sample cutting data exceeds the media
width.
•Two-point axis alignment is set to ON.
•Marks have already detected.
Division cutting is not allowed.
29
COPY SKIP
A mark could not be detected during con-
tinuous copying. (One pattern is skipped.)
There is no problem if the marks are successfully detected
after skipping one pattern.
If marks cannot be detected successively by five patterns or
more, [ERROR 36-C MARK DETECT] is displayed.
30
PAUSE REM/END
Since [REMOTE] was pressed during
mark detection, the detection operation
has come to a halt.
Press [REMOTE] again to resume detection operation.
Or press [END] to terminate the operation.
31
MEDIA SKEW <ENT>
The deviation of the media exceeded the
setting value of SKEW CHECK.
Set the media again and press [ENTER].
32
MEDIA EXCHANGE
Replacing the media is being waited for.
(During continuous copying on cut
sheets)
Change leaf media (cut sheets) and resume continuous copy-
ing.
33
MEDIA END REM/END
The media end was detected during mark
detection or during cutting in roll media.
The end of the roll media has been reached, thus cutting can-
not be continued.
Press [END] and replace the media with new one.
The media is floating. Set the media properly so that it is free of floating, and press
[REMOTE] to resume cutting.
A strong light hits the rear of the
machine.
Intercept the light, and press [REMOTE] to resume cutting.
R.1.2
Maintenance Manual > Troubleshooting > Details on Errors and Malfunctions > List of Warning Messages
Model CJV30/TPC Issued 2008.08.04 Revised 2009.08.25 F/W ver. 2.00 Remark
1.2
Rev.