© 2009 MIMAKI ENGINEERING CO.,LTD.
7.1.2
P.2
7.1.2 List of Error Messages
12C
ERROR 12-C
DEVICE
Inappropriate instruction was given concerning the
printer controlling.
Modify the instruction and send the data again, or
send the data after restarting the printer.
If the abnormality occurs again, carry out the fol-
lowings.
1. Clear the data of uncompleted printing.
2. Check the USB cable.
(specifications, cable length, etc.)
3. Replace the main PCB assy. (
13C
ERROR 13-C
PM OVER
The polygon data exceeded the receive buffer.
Divide the polygon data before sending them.
15C
ERROR 15-C
AUTO FEED
Media feeding cannot be carried out according to
the length specified by the data.
Set a longer media and carry out the operation
again.
16
ERROR 16
MRL COMMAND
Received data does not follow the command sys-
tem set in the printer.
Send the data related to the class of commands,
using an application corresponding to this printer.
1. Make sure that the transmission data is in
MRL-III command system (data ripped for
CJV).
25
ERROR 25
FULL-SPEED
USB2.0 interface occurred between the host PC
and the printer. (Full-Speed Mode connection)
Check whether the host PC is USB2.0 interface-
compliant or not. (Though the host PC can be used
in either case, use of Hi-Speed Mode connection is
recommended.)
ERROR 25
PACKET SIZE OVER
USB2.0 interface occurred between the host PC
and the printer.
1. Make sure that the connection to the host PC is
correct.
2. Make sure that there is no occurrence of an
error in the host PC or the application runs nor-
mally.
ERROR 25
USB PROTOCOL
USB2.0 interface occurred between the host PC
and the printer.
ERROR 25
USB ENVIRONMENT
USB2.0 interface occurred between the host PC
and the printer.
ERROR 25
USB DATA
USB2.0 interface occurred between the host PC
and the printer.
30
ERROR 30
OPERATION ERROR
Improper operations were performed on the opera-
tion panel.
The operation cannot be carried out due to the rea-
son indicated in the second line.
Clear the corresponding error and carry out the
operation.
31C
ERROR 31-C
NO DATA
[No. COPIES] cannot be carried out due to the
absence of data in the receive buffer.
(Refer to the page of [No. COPIES] function in the
OPERATION MANUAL.)
32C
ERROR 32-C
DATA TOO BIG
[No. COPIES] cannot be carried out due to the
large size of the received data.
33C
ERROR 33-C
MEDIA SIZE
Media is too short in the length of the feed direc-
tion.
Use longer media.
34
ERROR 34
PRINT DATA REMAIN
Functional settings were changed or an inoperative
function was attempted while the printer has
already received data and printing of the data has
not been completed.
Print all the data received, or clear them all and
carry out the operation again from the start.
(If uncompleted printing data is remaining, provide
an account concerning the operating-condition
modification and the inoperative function.)
34C
ERROR 34-C
CUT DATA REMAIN
An inappropriate operation was carried out during
the cutting was being suspended by pressing
[REMOTE] key.
Wait for the cutting data to be completely carried
out or clear the data.
35C
ERROR 35-C
cutNG WIND
Since take-up is executed, auto cutting of media is
not performed.
Auto cutting is not performed if take-up timing is
set by the roll detection setting function.
To give priority to auto cutting, set [TAKEUP TIM-
MING] to OFF.
List of error messages (2/6)
Error
No.
Indication on LCD
Cause
Remedy
R.1.1
Maintenance Manual > Troubleshooting > Details on Errors and Malfunctions > List of Error Messages
Model CJV30/TPC Issued 2008.08.04 Revised 2008.09.17 F/W ver. 1.20 Remark
1.1
Содержание CJV30 Series
Страница 315: ......
Страница 316: ...Printed in Japan D500387 13 05112010 2010 MIMAKI ENGINEERING CO LTD IT FW 2 5...
