MIMAKI CG-100SRIII Скачать руководство пользователя

Страница: 53 / 172

3-3

Useful Function

Functions in the Jog Mode

Two-point axis alignment

If a ruled sheet is set, align the horizontal and vertical axes with the
appropriate lines on the sheet.
Correct the axial inclination (

) by setting a compensation point in

combination with the origin.

Press the

key to set to the local mode.

• Confirm in advance that even if you press the

key to enter

the remote mode, the plotter does not perform cutting (plotting).

Set the Origin by pressing the jog key

to and press the

key.

Press the jog key

to enter

the jog mode.

• Press either one of the jog keys, and you can enter the jog mode.

Press the

key.

Press the jog key

to set

the compensation point.

•

= -45 to 45 degrees

Press the

key to decide the origin.

• The display is as shown on the right briefly, after which the plotter

returns to the local mode.

• When you clear the compensation point, move the clamp lever to the rear side to make the clamp

OFF and perform sheet detection (

P.2-14

) again.

Origi

Compensation point

REMOTE

ENTER/HOLD

SHEET

ENTER/HOLD

Содержание CG-100SRIII













































































































































































Результаты поиска

Содержание CG-100SRIII

Отзывы:

Похожие инструкции для CG-100SRIII

Бренды по названию

Популярные бренды

MIMAKI CG-100SRIII, Руководство по эксплуатации

Результаты поиска

Содержание CG-100SRIII

Отзывы:

Похожие инструкции для CG-100SRIII

Бренды по названию

Популярные бренды