Miller ENPAK страница 46 Скачать руководство пользователя

Страница: 46 / 96

OM-261050 Page 42

SECTION 10

−

OPERATION

10-1. Remote Devices Connections

265 802-A / 287 097

EnPak Remote Panel Connection

Receptacle RC12

Mount remote panel inside of truck body

cabinets where easily accessible. Connect

interconnecting cable Part No. 244283

between remote panel and RC12.
2

Crane Remote Connection

Receptacle RC13

NOTICE

−

Connect to this receptacle only

when EnPak is equipped with hydraulic

power source used to power a hydraulic

crane apparatus.

Crane remote control provided by crane

manufacturer. Connect appropriate har-

ness adapter into the crane harness (see

instructions provided with harness adapter

kit). Connect interconnecting cable Part

No. 244283 between crane remote and

RC13.
Contact Factory for list of harness adapters

available.

Optional Engine Remote Start/Stop Us-

ing Ground Signal

Service Panel

Locate wire 120 in the harness close to the

Service Panel control board. It will have a

fast on connector on the end of it.

Connect signal wire from start/stop switch

to this wire 120 and route the wire out

through the base of the unit. The signal

from the switch must be a “ground” signal

when the switch is activated and no signal

when the switch is not activated.

The EnPak control will detect a ground sig-

nal and will start the engine if it is not run-

ning, or it will stop the engine if it is running.

Содержание ENPAK

































































































Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды

Miller ENPAK, Руководство пользователя

Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды