Miller ENPAK Скачать руководство пользователя

Страница: 26 / 96

OM-261050 Page 22

5-2. Mounting Unit

Tools Needed:

9/16 in.

Welding Unit In Place

Bolting Unit In Place

NOTICE

−

Do not mount unit by

supporting the base only at the four

mounting brackets. Use cross-sup-

ports to adequately support unit

and prevent damage to base.

See Section 4-7 for dimen-
sions.

Mounting Surface:

Cross-Supports

Mounting Brackets (Supplied)

Mount unit on flat surface or use

cross-supports to support base.

Secure unit with mounting brack-

ets.
3

1/2 in Bolt And Washer

(Minimum

−

Not Supplied)

5/16-18 x 3/4 in. Screws

(Supplied)

To Bolt Unit In Place:

Using brackets attached to the

base, mount unit to vehicle with 1/2

in. (12 mm) or larger hardware (not

supplied). There are also 3/8 in.

weld nuts and mounting holes in the

base. See Section 4-7 for mounting

dimensions.

To Weld Unit In Place:

Remove hardware securing the

four mounting brackets to the base.

Reverse brackets and reattach to

base with original hardware.
Weld unit to vehicle only at the four

mounting brackets.

Supporting The Unit

Using Mounting Brackets

Ref: install3 2008--01 803 274 / 200 864-A / 265 802-A

Содержание ENPAK

































































































Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды

Miller ENPAK, Руководство пользователя

Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды