Miller ENPAK Скачать руководство пользователя

Страница: 40 / 96

OM-261050 Page 36

8-3. Compressor Prestart Checks

Ref. 265 802-A

Do not open oil fill cap until unit is

off and pressure in the compressor

case has been released according

to Section 8-5. Do not open oil fill

cap while running.

The compressor is equipped with high
oil temperature shutdown. High oil

temperature can be caused by low oil

or hot air recirculation.

NOTICE

−

Do not mix oil types. Do not

overfill.

Air Compressor Oil Fill Cap

Hand tighten oil fill cap. Using excess

force can damage o

−

ring.

Oil Level Sight Gauge

The unit is shipped with oil in the com-

pressor reservoir. Oil level sight gauge

shows oil level.
Minimum oil level is half way up the oil fill

pipe. Maximum oil level is in threaded area

of oil fill pipe.
Check level frequently. If oil needs to be

added, be sure unit is off and compressor

case pressure is released according to

Section 8-5 before removing fill cap.

Minimum com-
pressor oil level

is half way up

the fill pipe.

Maximum oil

level is in

threaded area

of oil fill pipe.

High

Low

Содержание ENPAK

































































































Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды

Miller ENPAK, Руководство пользователя

Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды