Miller ENPAK Скачать руководство пользователя

Страница: 35 / 96

OM-261050 Page 31

7-3. Priming Hydraulic Pump

265 795-A / 265 802

−

A / 260 718B

When working on unit, always

move Manual/Remote switch to

Manual position to prevent remote

starting. See Section 10-7.

Proportional Valve Assembly

Manual Override Screw Adjust

Service Panel

Manual/Remote Switch

Fuel Pump Switch

Make hydraulic system connections ac-

cording to Section 7-2.

Check to be sure hydraulic pump case oil

is at its highest point.
Fully open suction line valve at the reser-

voir. Turn manual override screw fully

clockwise (fully opens proportional valve).
On Service Panel, place Manual/Remote

switch in the Manual position. Place the

Fuel Pump switch in the Off position.
Crank the engine for 10 seconds, pause,

crank again for 10 seconds, pause and

crank for an additional 10 seconds. This

should prime the hydraulic pump.

Turn the manual override screw fully coun-

terclockwise.
Place the Service Panel Manual/Remote

switch in the Remote position. Place the

Fuel Pump switch in the On position.
Start the engine using the remote panel.

Let the engine run 5 to 10 minutes with no

load.
Pressure and flow rate are set at the fact-

ory and should not require initial adjust-

ment. Have Factory Authorized Service

Agent correct settings.

Содержание ENPAK

































































































Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды

Miller ENPAK, Руководство пользователя

Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды