Miller ENPAK Скачать руководство пользователя

Страница: 49 / 96

OM-261050 Page 45

10-5. Operation And Error Messages

Alpha

−

Numeric Display

The following operational messages

may appear:
CHNG OIL

Indicates an oil change is needed. This light

flashes after the first 50 hours of operation

and then at normal oil change intervals

thereafter.
If CHECK ENGINE LED is on, engine oil

change time interval has counted down to

zero, indicating it is time to change engine

oil.
To reset display after oil change, see Sec-

tion 11-4.
If CHECK COMPRESSOR LED is on,

compressor oil change time interval has

counted down to zero, indicating it is time to

change compressor oil.
To reset display after oil change, see Sec-

tion 11-5.

HIGH SPd

Indicates engine is locked in high speed.

With engine running, press Power/Start

button to toggle speed.

AUTOSTOP

This will flash briefly when unit is in Auto On

mode and the engine stops automatically.

The following error messages may ap-

pear:

If error message appears, consult
troubleshooting section for remedial

actions.

Hi TEMP

Indicates high compressor temperature if

CHECK COMPRESSOR LED is on.

OVErPRES

Indicates the compressor has an over pres-

sure error.

OVErSPEEd

Indicates an engine over speed error.

LOW OIL

Indicates a low oil pressure condition in the

engine.

NoCHARGE

Indicates an alternator problem.

HiTEMP 1

Indicates high engine temperature if

CHECK ENGINE LED is on. The temperat-

ure switch has indicated high temperature.

HiTEMP 2

Indicates high engine temperature if

CHECK ENGINE LED is on. The temperat-

ure sensor has indicated high temperature.

SPd SENS

Indicates a problem with the engine speed

sensor.

GovCNTRL

Indicates a problem with the engine gov-

ernor control.

SEN OPEN

Indicates coolant sensor is open.

SENSHORT

Indicates coolant sensor is shorted.

ALTRNATR

Indicates an open condition in the alternat-

or.

HiVOLTiN

Indicates high input voltage from the bat-

tery.

LoVOLTiN

Indicates low input voltage from the battery.

ERROR

Indicates an engine error, and the error is

stored in memory. If the display is off, press

the Power push button once to activate the

Remote Panel. The display will read ER-

ROR and after a few seconds will flash an

error code. See Table 10-1.
To erase the error, press and hold the Dis-

play Select push button until the display

reads SYSTEMon, and the indicator is off.

The display will now cycle normally when

the Display Select push button is pushed.

ERROR1

Indicates problem with crane remote inter-

connecting cable, plug, receptacle, or ad-

apter harness.

ENVRT hot

Indicates the EnVerter power system is

overheated.

ENVRT ok

Indicates the EnVerter power system is

functioning. Press Power/Start button to

enable.

248 998

Содержание ENPAK

































































































Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды

Miller ENPAK, Руководство пользователя

Результаты поиска

Содержание ENPAK

Отзывы:

Похожие инструкции для ENPAK

Бренды по названию

Популярные бренды