Microsemi SyncServer S600 Скачать руководство пользователя страница 230

Страница: 230 / 252

230

SyncServer 600 Series User’s Guide

098-00720-000 Revision B – April, 2016

Appendix C Installing GNSS Antennas
GNSS Antenna Installation

Connecting the Cable to the Antenna

This section describes how to connect the coaxial cable to the mounted antenna.
See

Figure C-6

1. Connect the 25 ft. cable to the antenna.

2. Connect the other end of the 25 ft. cable to the lightning arrestor.

3. Connect the lightning arrestor to the long cable.

4. Connect the other end of the long cable with the 4 ft. BNC-N adapter cable.

Installing the Lightning Arrestor

Lightning arrestors should be installed in accordance with your antenna system
grounding scheme. To install a lightning arrestor, follow these steps:

1. Mount the lightning arrestor within 30 ft. (9 m) of the GNSS antenna.

2. Connect the ground wire between the lightning arrestor and the proper grounding

zone (building ground, master ground bar, or other) for the mounting location.

3. Wrap the connectors with weatherproof tape for added protection.

4. Verify that the antenna coaxial cable center conductor is not shorted to the shield of

the cable.

Caution:

To avoid damage to the connectors, do not use the

connectors to pull the cable. If at all possible, avoid bundling the
coaxial cable with other cables (and possible noise sources). Use
appropriate cable-pulling devices when pulling the coaxial cable
through conduit or a weather head.

Caution:

To avoid damage to internal solder connections, do not

over-tighten the connector.

Recommendation:

Microsemi does not recommend soldered

connections for grounding purposes. All grounding connections
should be secured with mechanical clamp connectors.

Содержание SyncServer S600





























































































































































































































































Результаты поиска

Содержание SyncServer S600

Отзывы:

Бренды по названию

Популярные бренды

Microsemi SyncServer S600, Руководство пользователя

Результаты поиска

Содержание SyncServer S600

Отзывы:

Бренды по названию

Популярные бренды