Microsemi SyncServer S600 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 252

background image

136

SyncServer 600 Series User’s Guide

098-00720-000 Revision B – April, 2016

Chapter 6 Provisioning
Establishing a Connection to the SyncServer S6x0

Establishing a Connection to the SyncServer S6x0

There are four ways to bring the SyncServer S6x0 on line:

1. The SyncServer S6x0 default IPv4 address for port LAN1 is 192.168.1.100, the

subnet mask is 255.255.255.0, and the gateway address is 0.0.0.0 (no gateway).
These may be suitable.

2. Use the front panel to input the IP address, subnet mask and gateway.

3. Use the front panel to turn on DHCP and review the assigned address.

4. Use the serial port

Communicating Through LAN1 Ethernet Port

The LAN1 Ethernet port must be set to an IP address that is compatible with your
network to allow communication. If the default IPv4 address (indicated above) is not
acceptable, you must first configure Ethernet LAN1 port through the EIA-232 serial
port with CLI commands or with the front panel.

Once the LAN1 port has been configured, it can be used to access the SyncServer
S6x0 web interface. Connect the LAN1 port to your network with a CAT5 Ethernet
cable. Enter the LAN1 port IP address into a web browser. Enter your user name
and password for the SyncServer S6x0 when prompted.

HTTPS

A certificate is required with HTTPS. The SyncServer S6xx uses a self-signed
certificate rather than a certificate generated by a known certificate authority.
Browsers will therefore give warnings when attempting to connect to the
SyncServer S6x0. Users will need to allow the browser to continue. The actual
messages and screens will be different for different browsers. Certificates have an
expiration date. After the built-in certificate expires, a new certificate can be
generated on the Security->https page.

shows an example HTTPS message from the Google Chrome browser.

Clicking the Advanced button brings up the message shown in

shows an example HTTPS message from the Mozilla Firefox browser.

Clicking the Advanced button brings up the message shown in

Note:

The default user name is “admin”. The default password is:

Microsemi.

«
...
136
137
138
139
140
...
»

Содержание SyncServer S600





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SyncServer S600

Бренд: Panasonic Страницы: 31

Бренд: F5 Страницы: 2

WANJet 400 Appliance

Бренд: F5 Страницы: 11

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 194

ApplianceStor 15MT

Бренд: Rasilient Страницы: 30

Lynx DSS L106-S2 EX

Бренд: Westermo Страницы: 28

Бренд: Digi Страницы: 163

Бренд: Hitachi Страницы: 58

Бренд: Hitachi Страницы: 192

AAEON ARES-WHI0

Бренд: Asus Страницы: 76

Бренд: Asus Страницы: 16

Бренд: Asus Страницы: 42

RS720A-E9-RS24-E

Бренд: Asus Страницы: 162

Бренд: Asus Страницы: 164

TS700-E9 Series

Бренд: Asus Страницы: 178

Бренд: Asus Страницы: 224

Бренд: Asus Страницы: 162

Бренд: Asus Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды