Microsemi SyncServer S600 Скачать руководство пользователя страница 172 | Manualshive

Страница: 172 / 252

background image

170

SyncServer 600 Series User’s Guide

098-00720-000 Revision B – April, 2016

Chapter 7 Maintenance, Troubleshooting & Part Numbers
Upgrading the Firmware

Upgrading the Firmware

You can upgrade the firmware using the SyncServer S6x0’s web interface and
software available from Microsemi. When the SyncServer S6x0 is in the firmware
download mode, it prevents all other sessions from making changes to the
configuration. During the upgrade process, no new sessions are allowed. Refer to

SyncServer S6x0 Upgrade

below for details on the upgrade process. For releases

after 1.1, if the upgrade process is used to load a previous (older) version of the
software, then the unit will reset the configuration to factory default values.

The current firmware version can be found in the Dashboard > About window.

Upon receipt of any new/repaired equipment, perform the relevant software
upgrade procedure below prior to putting the shelf into service.

SyncServer S6x0 Upgrade

The upgrade process is simple, but there will be Loss of Service (LOS) at reboot.
The upgrade will take approximately 7 minutes to complete. The upgrade process
requires an authorization file in order to proceed. This file verifies that this
SyncServer unit is authorized to upgrade the selected upgrade file.

The SyncServer 6x0 does not contain a battery-backed real time clock. Therefore, it
will always boot up with a default value for the system time. This time will be
updated when it obtains time from a time reference such as GNSS, IRIG, or NTP.
The default value for the date is the software build date. This date will be used for
the first log entries when booting up the unit. The time will change to local time
during the boot-up process if a time zone has been configured.

Caution:

To avoid a possible service call, do not issue a command to

the SyncServer S6x0 during an upgrade and do not remove power
from the SyncServer S6x0 during an upgrade. Doing so could corrupt
the flash memory, disabling the SyncServer S6x0.

«
...
170
171
172
173
174
...
»

Содержание SyncServer S600





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SyncServer S600

SuperServer E100-8Q

Бренд: Supermicro Страницы: 48

x3800 - System - 8865

Бренд: IBM Страницы: 104

8676 - Eserver xSeries 335

Бренд: IBM Страницы: 172

callpilot 1002rp

Бренд: Avaya Страницы: 150

Бренд: Belkin Страницы: 2

Бренд: Supermicro Страницы: 113

Бренд: Xblue Networks Страницы: 2

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 52

Бренд: Huawei Страницы: 122

Бренд: Huawei Страницы: 131

UPS5000-E-****-FM series

Бренд: Huawei Страницы: 261

Turbo NAS TS-219P

Бренд: QNAP Страницы: 49

Бренд: IBM Страницы: 2

System x3100 M4

Бренд: IBM Страницы: 35

eServer xSeries 345 Type 8670

Бренд: IBM Страницы: 71

eServer 445 xSeries

Бренд: IBM Страницы: 124

pSeries 615 Model 6C3

Бренд: IBM Страницы: 208

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды