MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 50

MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 36

MHS Boilers Ltd ©

191007

36

Operating mode (cover closed)

With the cover closed and by using the Rotational Selector (pos. No. 2) clockwise or anti-clockwise
the boilers’ operating mode can be set.

The operating modes are:-

standby

the boiler switched off but frost protection is active

automatic

the boiler can operate in heating or hot water mode

summer mode

the boiler will only react to a hot water demand

service,

low capacity the boiler will run at low capacity (adjusted by [P17])

service,

high capacity the boiler will run at full capacity (adjusted by [P19]).

Information mode

With the cover open and by turning the rotational switch (Pos. No 5) clockwise or anti-clockwise it
is possible to read out certain information from the boiler management unit.
There are 10 possibilities. An arrow at the bottom of the LCD display will indicate which parameter
has been selected. The following parameters are readable:-

Parameter

P1 actual/setting flow temperature
P2 actual/setting direct hot water temperature (if used)

P3 set point temperature (* P3 set load in comb. with KKM8/E8)
P5 actual outside temperature (if used)
P8 temperature at the low velocity header (if used)
P9 actual / setting boiler capacity
P10 only for MHS trained service engineers. (Password protected)

Summary of input and output indications (cover open)

Input indications: -

Flame Ionisation detected

SW

Water flow switch in operating position

DW

Air Pressure Switch in operating position

RT

Boiler enabled by Volt Free Enable. Required under all control options.

Bus

Data-bus detected. BM8 / KKM8 / E8

Output indications: -

Power to Main Gas Valve

Power to Ignitor

Control signal to fan

Power to Primary Boiler Pump

Power to Primary DHW Pump.

«
...
34
35
36
37
38
...
»

Содержание Ultramax WM 100



















































Отзывы:

Нет отзывов