MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 50

MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 27

MHS Boilers Ltd ©

191007

27

• Type C83:

Room Sealed appliances in cascade, connected to separate air supplies but common flue discharge
through the roof.

5.3.4.2 Air inlet pipe

The air supply pipe may be single wall, smooth or flexible, and be made of:
• plastic
• aluminium
• stainless steel
Always consider the large resistance when using flexible material.
Always consider condensate formation due to the suction of cold air.

Type

Diameter of air inlet D1 (mm)

WM/45 80

WM/65 80

WM/85

100

WM/100

100

WM/120

100

Table 3 Diameter of air inlet

The connection for the air supply is on the top of the boiler.
The air supply pipe should be airtight. This is to prevent the suction of ‘false air’. Horizontal
components in the air supply should be installed sloping in the direction of the supply opening.(Fresh
air opening)

5.3.4.3 Flue gas outlet

The flue gas components may be single wall, smooth, Rigid or flexible, and be made of:
• plastic
• stainless steel
Always consider the resistance when using flexible material.

Type

Diameter of Flue Gas D (mm)

WM/45 80

WM/65 80

WM/85

100

WM/100

100

WM/120

100

Table 4 Diameter of flue gas outlet

The flue gas outlet is located on the top of the appliance and is designed for direct connection to a
corrosion resistant flue pipe.

«
...
25
26
27
28
29
...
»

Содержание Ultramax WM 100



















































Отзывы:

Нет отзывов