MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 50

MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 12

MHS Boilers Ltd ©

191007

12

3 Safety

Installation specifications

Read the specifications before commencing with installation.
The equipment should be installed by a recognised installer in accordance with applicable national
and local standards and specifications.
The installation should only be used for heating systems with a maximum water temperature of
90

°

C.

It is expressly stated that these installation specifications should be regarded as a supplement to
the above mentioned standards and specifications, which shall take priority over the information
contained in this technical documentation.

Maintenance

Work on the electrical installation should only be carried out by a recognised installer in accordance
with the applicable electrical regulations.
Work on the gas equipment and hydraulic installation should only be done by personnel having
the required training, in accordance with the applicable safety rules and regulations for gas
installations.
Do not place any objects on the boiler. Keep a safe distance from the hot water connection and the
flue, due to the danger of burns.
Before starting with any maintenance and service work, shut off the electrical supply and close
the gas valve to isolate the gas supply.
Check the entire installation for leakages after completing maintenance and service work.
Casing parts may only be removed for maintenance and service purposes. After carrying out
maintenance and service work, replace all the panels.

Safety devices

The installation should never be switched on with the casing panels removed unless undertaking
repairs or preventative maintenance or the safety devices disabled.

Instructions and warning stickers

Instruction and warning stickers affixed on the appliance should never be removed or covered up,
and should be maintained in a legible condition throughout the life of the appliance. Immediately
replace damaged or illegible instruction and warning stickers.

Modification

The appliance may only be modified with the written permission of the manufacturer.

Danger of explosion

While doing work in the boiler room, follow the applicable rules and regulations entitled ‘Working
in Areas Subject to Danger of Explosion’.

«
...
10
11
12
13
14
...
»

Содержание Ultramax WM 100



















































Отзывы:

Нет отзывов