MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 50

MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 13

MHS Boilers Ltd ©

191007

13

Installation

The appliance should be installed by a recognised installer in accordance with applicable national
and local standards and specifications.
Follow all the safety instructions precisely.

Operation

In case of a gas leakage: Prevent the boiler from operating and close the gas valve. Open doors and
windows
and notify the relevant authorities.
When the appliance is restarted, follow the user instructions.

Technical specifications

The specifications contained in this technical documentation should not be exceeded.

4 Delivery and transport

4.1 Delivery

The boiler is delivered fully assembled, tested, and packed.
Check the boiler for damage after receipt.
Check whether the items delivered are correct and in accordance with the items ordered.

4.2 Packaging

The boiler is delivered in suitable cardboard packaging.
The types 45, 65, 85 and 100 can be stacked two high. It’s not allowed to stack up the type 120.

4.3 Transport

Regarding transportation, refer to the technical data for dimensions and weights.
The packing should only be removed after transportation, or remove the panels before transportation.
This is in order to prevent the panels from getting damaged.

Moving

Each boiler is packed in its own carton which has hand holed at both sides for lifting purposes.

Access requirements

The dimensions of the boiler are such that all the boiler types can be transported through a door
opening of 60 cm.

Mounting

Install the WM using a spirit level on a sufficiently sturdy non-combustible wall using the suspension
bracket provided. A template has been provided in the packing box, on which the positions of the
fixing holes have been indicated.

Protection against frost

Boilers that are not used during the winter are in danger of freezing. Drain the system or add suitable
inhibitor.

«
...
11
12
13
14
15
...
»

Содержание Ultramax WM 100



















































Отзывы:

Нет отзывов