MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 50

MHS Boilers Ultramax WM 100 Скачать руководство пользователя страница 18

MHS Boilers Ltd ©

191007

18

E8.1121

This is a control system for the weather dependent control of two secondary heating circuits. In
addition, a hot water circuit can also be controlled at two different Set Points. All the settings can
be made separately for each secondary circuit. This E8 controller can be further extended with an
optimisation controller system for each secondary group (BM8). The weather dependent control of
the boiler is done indirectly by the E8.1121.
There are the following additional features to the BM8:
- The maximum flow temperature can be set for each heating circuit
- The compensation slope can be manipulated with a parallel displacement to the desired flow
temperature of the boiler
- Time controlled hot water Secondary pump
- Pump-exercise function
- DCF receiver for internal clock (optional receiver required)
- Communication over a CAN-bus
- Integrated relay and sensor test
- Can be used in stand-alone operation

Controller Wiring Terminals.(Rear of controller)(Housing available)

«
...
16
17
18
19
20
...
»

Содержание Ultramax WM 100



















































Отзывы:

Нет отзывов