Mhouse MhouseKit WS2S, Руководство по установке

Страница: 26 / 36

24
TECHNICAL CHARACTERISTICS OF THE VARIOUS COMPONENTS OF THE PRODUCT
The product WS2S is produced by Nice S.p.a. (TV) I, Mhouse is part of the NICE S.p.a. group. In order to improve its products, NICE S.p.a. reserves
the right to modify the technical characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness
for the intended purposes. Note: all the technical specifications refer to a temperature of 20°C.
Programmable functions
Self-programmed functions
The structural design of this product makes it suitable for use on gates with a weight up to 200 kg or
leaf width up to 2.2 m. Opening angle 110°
Model/type WS1SC WS1SK
Type
Electromechanical gearmotor for the automation of automatic gates and doors with built-in control unit
complete with radio receiver for “GTX4” transmitters.
Adopted technology
24 VDC motor, helical gear reducer; mechanical release. A transformer incorporated inside the motor
but separated from the control unit reduces the mains voltage to the nominal 24 V
voltage used in
the whole automation system
Maximum torque on start-up 150 Nm
Nominal torque
50 Nm
Idling speed 1.7 RPM
Speed at nominal torque
1.4 RPM
30 cycles/hour at 50 °C Maximum frequency of cycles
Maximum continuous cycle time 10 minutes
Operating Limits
Mains power supply WS1C- WS1
Nominal absorbed power
230 V (+10% -10%) 50/60Hz
Rated current absorption
-
1.1 A, on start-up, maximum current is 3.5 A for a
maximum time interval of 2 s
Emergency power supply For “PR1” buffer batteries
Flashing light output For flashing lights with 12 V bulb, maximum 21 W
ECSbus output One output with a maximum load of 15 ECSbus units
“OPEN” input
For normally open contacts (the closing of the contact causes the “OPEN” command)
“STOP” input
For normally open contacts and/or for 8.2K Ω constant resistance type contacts, or normally closed
contacts with recognition of the “normal” status (any variation with respect to the memorised status
generates a “STOP” command)
Radio aerial input 52 Ω for RG58 or similar type cable
Maximum cable length
Mains power supply: 30 m; inputs/outputs: 20 m with aerial cable preferably shorter than 5m (observe
warnings regarding the minimum section and type of cable)
Ambient operating
temperature
-20 ÷ 50°C
Use in particularly acid, saline or
potentially explosive atmospheres
NO
Assembly Horizontal on a flat surface with the specific fixing plate
Protection rating IP54
Dimensions / weight 237 x 146 h 290 mm / 6.5 kg 237 x 146 h 290 mm / 6.2 kg
Remote control possibility
With GTX4 transmitters, the control unit can receive one or more of the following commands: “OPEN”,
“Partial opening”, “Open only” and “Close only”
GTX4 transmitters memorised Up to 150 if memorised in mode 1
Range of GTX4 transmitters
From 50 to 100 m. The range can vary if there are obstacles or electromagnetic disturbances, and is
affected by the position of the receiving aerial incorporated in the flashing light.
“Cycle” or “Complete cycle” operation (automatic closing)
“Slow” or “fast” motor speed
The pause time in the “complete cycle” mode can be set at 10, 20, 40, 80 seconds
Type of partial opening selectable from 4 modes
The sensitivity of the obstacle detection system can be selected from 4 levels
The operation of the “Open” command can be selected from 4 modes
Automatic detection of devices connected to the ECSBus output
Automatic detection of the type of “STOP” device (NO or NC contact or 8.2K
Ω resistance)
Automatic detection of the opening angle for each motor
Automatic detection of the automation with 1 or 2 motors
24 VDC
120 W; on start-up, maximum current is 310 W
for a maximum time interval of 2 s