Metz eta plus ELC X-Series eta plus ELC X4-40 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 62

Metz eta plus ELC X-Series
eta plus ELC X4-40 Скачать руководство пользователя страница 5

1

Safety

page 1

ELC X-Series-V1.3-09.16-GB

subject to technical alterations

1 Safety

1.1 Definition of symbols

Stop (Stop Danger). This symbol warns of serious danger of severe injury to
persons. It must be strictly observed.

Attention (Warning). This symbol indicates information the non-observance of
which can lead to extensive damage to property. The safety warning must be
strictly observed.

Information. This symbol indicates key information on use. Non-observance can
lead to failure.

1.2 Safety advice

The ELC must be installed and connected in compliance with existing regulations
and practices. This is e.g. EN 60204-1 in Europe.

Repairs on the ELC may only be carried out by the manufacturer.

The installation and starting up may only be carried out by skilled electricians.

Do not open the ELC before it is disconnected from the mains. BEWARE OF
RESIDUAL VOLTAGE! The unit may still be live up to several minutes (see
chapter 6) after it has been switched off.

☞

«
...
3
4
5
6
7
...
»

Содержание eta plus ELC X-Series eta plus ELC X4-40































































Отзывы:

Нет отзывов