Metz eta plus ELC X-Series eta plus ELC X4-40 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 62

Metz eta plus ELC X-Series
eta plus ELC X4-40 Скачать руководство пользователя страница 29

3

Installation

page 25

ELC X-Series-V1.3-09.16-GB

subject to technical alterations

3.4.2 Checking the PROFIBUS connection and error indication

The display may be used to check the successful connection of ELC and Master and
furthermore the existence of an error (ELC not ready for operation). It is also possible to read
out error messages within the [Error Register] see paragraph 5.4.1 (detailed explanations may
be found there).

Display

Status

Corrective action

ELC

ready

for

operation, PROFIBUS-
connection ok

ELC

ready

for

operation,

no

PROFIBUS-connection

Check plug contact, bus
termination (see
paragraph 3.2.11), check
address and panel-
programming.

(If there is more than one error
message at hand, briefly press the
SET-button to jump to the next error
message.)

ELC not ready for
operation, PROFIBUS-
connection ok

The error cause
detected by the ELC is
displayed and may be
read out additionally in
the Error Register (see
paragraph 5.4.1).

ELC not ready for
operation,

no

PROFIBUS-connection

Check

PROFIBUS-

connection.

Detach ELC from mains
and restart.

Display won’t turn on
(display defect or no
supply)

Check 24V supply,
switch off and on again.

ELC ready

BUS connected 19h

ELC ready

No BUS

19h

Error message

BUS connected 19h

Error message

No BUS

19h

«
...
27
28
29
30
31
...
»

Содержание eta plus ELC X-Series eta plus ELC X4-40































































Отзывы:

Нет отзывов