Metso 25411801001/A5684 Скачать руководство пользователя

Страница: 54 / 85

Slurry Pump

WH18AA11D00EN_01G.DOC

JAN

04-W08

Care and maintenance

4/4

Closing the pump

If the Front Pull-Out Method was used:

i/ Lift and push the case over impeller (W3), onto back-liner (W4) and against

the vertical plate. Ensure that case fixings (B) enter their respective holes
around the flange joint.

ii/ Locate and secure the case to the vertical plate by fitting the upper and

lower casing clamp fixings (C) in the case slots provided.

If the Back Pull-Out Method was used:

i/ Lift and offer the complete bearing frame and rotating assembly onto the

base/case-support and push the impeller and back liner into the case with
approximately a 30mm gap between the bearing frame flange and the
vertical plate.

ii/ Insert bearing frame screws (P11) and washers (P12). Do not tighten at this

stage.

Set the impeller front clearance –see section 9.5.1.

Check the impeller for freedom of rotation.

NOTE

AFTER FINAL ADJUSTMENT

THE BACK

LINER WILL NORMALLY PROTRUDE

SLIGHTLY INTO THE CASE

–

EXCEPT FOR HM

AND HM

WHEN FITTED WITH

INDUCED FLOW IMPELLERS WHICH USE A FLAT BACK

LINER

Tighten all fixings (B & C) to the torque values given in sub-section 11.1.

If the Front Pull-Out Method was used:

Check inlet and outlet gaskets and re-connect the respective pipework.

CAUTION

REFER TO SECTION

6.5

BEFORE RENEWING PIPE FLANGES

If the Back Pull-Out Method was used:

i/ Tighten the bearing frame screws.

ii/ If fitted, reset the mechanical seal for operation.

iii/ If fitted, reconnect the flush water tapping.

iv/ Fit the drive belts or connect the drive coupling, ensuring that they are in

correct alignment.

v/ Fit and secure the drive safety guard and the gland guard in position.

vi/ Check that all fixings are secure.

vii/ Remove warning plates and safety locks from power switches and restore

power supply to the motor.

Содержание 25411801001/A5684






















































































Результаты поиска

Содержание 25411801001/A5684

Отзывы:

Похожие инструкции для 25411801001/A5684

Бренды по названию

Популярные бренды

Metso 25411801001/A5684, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 25411801001/A5684

Отзывы:

Похожие инструкции для 25411801001/A5684

Бренды по названию

Популярные бренды