manualshive.com logo in svg

Metso 25411801001/A5684, Руководство по эксплуатации и техническому обслуживанию, Страница: 64 / 85

Поделиться
Скачать
Metso 25411801001/A5684 Скачать руководство пользователя страница 64

  
 
Slurry Pump 

 

 

WH201A1B010EN_01E.DOC 

JAN 

04-W08 

Care and maintenance

1/2

 

9.5.4 

Shaft and bearing assembly - removal and fitting 

The following instructions assume that the pump is installed complete with the drive unit 
and is connected to the suction and discharge pipework. 

 

1. Removal 

a) 

Remove the drive safety guard and disconnect the drive belts or drive coupling 
as applicable. 

b) 

If necessary, remove the drive motor to provide sufficient space to withdraw the 
bearing frame assembly from the case. 

c) 

Remove the wet end assembly (refer to sections 9.5.2 & 9.5.3) 

d) 

Where applicable, remove impeller release mechanism from the shaft – see 
section 9.5.2 (iii). 

e) 

Remove the housing clamp (P29) and cover (P24). 

f) 

Slacken the tension screws (P23), adjusting screw (P19) and locknut (P38).  
Remove the adjusting screw and retaining plate (P22). 

g) 

Remove the saddle screws (P20) and lift out the saddle (P18).  

h) 

Remove the grease nipple (B13) from the end cover at the wet-end of the shaft. 

i) 

Ease the shaft assembly rearwards out of the bearing frame.  When possible, 
especially on the larger pumps, fit a strop sling around the bearing housing to 
take the weight as it is withdrawn completely from the frame.  Remove the 
tension block (P21) as the assembly is withdrawn. 

j) 

Place the shaft and bearing assembly on suitable supports, ideally wooden vee 
blocks. 

 

2. Re-fitting 

a) 

Clean and degrease the bore of the bearing frame.  Coat the machined 
surfaces with anti-seize compound. 

b) 

Using a suitable strop sling to lift the assembly, insert the shaft and bearing 
assembly, threaded end first, into the bore of the frame. 

c) 

Rotate the bearing cylinder housing in the frame so that the tapped holes for the 
saddle screws are uppermost.  Fit the following parts into position: 

• 

Tension Block (P21) 

• 

Adjusting Screw (P19) into the saddle 

• 

Saddle (P18) (Do not fit screws at this stage) 

• 

Retaining Plate (P22) 

• 

Housing clamps (P29) and Housing clamp screws (P16) - tighten temporarily. 

d) 

Finally, position the bearing cylinder housing so that the saddle screws (P20) 
can be inserted and fully tightened to the correct torque.  See section 11.1. 

Содержание 25411801001/A5684






















































































Отзывы:

Нет отзывов