manualshive.com logo in svg

Metso 25411801001/A5684, Руководство по эксплуатации и техническому обслуживанию, Страница: 61 / 85

Поделиться
Скачать
Metso 25411801001/A5684 Скачать руководство пользователя страница 61

  
 
Slurry Pump 

 

 

WH19AM1G410EN_04C.DOC 

JAN 

04-W08 

Care and maintenance

2/4

 

d) 

If the centrifugal seal leaks when the pump is stationary, tighten gland follower 
(G10) by means of the gland follower screws (G18). 

CAUTION

  

DO NOT

 OVER

-

TIGHTEN THE SCREWS AS THIS WILL CAUSE SEVERE WEAR OF THE SHAFT SLEEVE

. 

 

3. Routine 

Adjustments 

Apart from the running checks specified above the only routine adjustments required are: 

a) 

To check the gland for leakage on stopping the pump and to adjust as 
necessary.   

b) 

When full adjustment of the gland follower has been taken up, packing rings 
(G5) should be renewed. 

c) 

Periodically lubricate the gland through grease nipple (G21). 

NOTE

:

THE AMOUNT OF GREASE INJECTED SHOULD BE A QUARTER OF THE QUANTITY INJECTED 

INTO THE MAIN BEARINGS AND AT THE SAME PERIODICITY AS THE MAIN BEARINGS 

-

SEE 

LUBRICATION

, 

SECTION 

9.4

.  

THE PERIODICITY AND QUANTITY GIVEN HERE ARE A GUIDE 

AND SHOULD BE MODIFIED IN LIGHT OF OPERATIONAL EXPERIENCE

. 

*

 

Figure 9.5.3-1  Arrangement of packing rings showing direction of rotation of the shaft (*) 

 

4. Renewing 

Packing 

a) 

Remove gland follower screws (G18). 

b) 

Slide gland follower (G10) away from the gland and remove the first two 
packing rings (G5) with a packing extractor. 

c) 

Charge the gland through grease nipple (G21). 

d) 

Insert two packing extractors, one each into diametrically opposite holes in 
lantern ring (G1), and extract it. 

e) 

Remove the last packing ring (G5). 

Содержание 25411801001/A5684






















































































Отзывы:

Нет отзывов