manualshive.com logo in svg

Metso 25411801001/A5684, Руководство по эксплуатации и техническому обслуживанию, Страница: 4 / 85

Поделиться
Скачать
Metso 25411801001/A5684 Скачать руководство пользователя страница 4

  
 
Slurry Pump 

 

 

WH03AA1AAA0en_03b.doc 

JAN 

04-W08 

General

1/6

 

1 

GENERAL 

1.1 

About this manual 

This manual is a part of the equipment to which it relates. It is written for the use of 
installers, commissioning engineers, operators and maintainers.  It should be kept for the 
life of the equipment and, in case of re-sale, passed on to any subsequent purchaser.   
 
Information contained in this manual is specific to the equipment and is correct at the date 
of publication.  As improvements are continually being made, 

Metso Minerals

 reserve the 

right to make alterations to the equipment design and specification without giving prior 
notice.  Any amendments issued by 

Metso Minerals 

should be promptly inserted into this 

manual. 
 

© 2004 — Metso Minerals (Sala) AB

.  The contents of this manual must not be 

reproduced without the prior written permission of 

Metso Minerals (Sala) AB

. 

 

1.2 

Transport and storage 

1.2.1 

Delivery 

A pump is either dispatched as an individual unit (bare shaft pump) or mounted complete 
with drive unit on a bedplate (pump-set).  In either case, any exposed machined parts are 
coated with a suitable rust inhibitor. 

 

Each pump is supplied complete with inlet and outlet flanges and gaskets, drive key, and 
with the bearing cylinder charged with grease. 
 
The packing or boxing will always be more than adequate for the method of shipment and 
subsequent storage. 
 
On receipt of the pump, check that the items listed on the consignment list have been 
supplied and have not been damaged in transit.  Ensure that the inlet and outlet apertures 
are clear and that the impeller runs freely when the shaft is turned by hand. 
 
If the pump has been disassembled for shipment, a consignment list will contain complete 
information on the identification of parts.  Where parts are boxed, each box is numbered 
and the corresponding number is noted on the consignment list. 
 
If damage has occurred or any items are missing, immediately file a report with the carrier 
making the delivery.  Also, submit a written report to 

Metso Minerals

 detailing the damage 

and/or missing items, as soon as possible.   
 

Содержание 25411801001/A5684






















































































Отзывы:

Нет отзывов