Metso 25411801001/A5684 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 85

Metso 25411801001/A5684 Скачать руководство пользователя страница 13

Slurry Pump

WH06AAAAAA0EN_02B.DOC

JAN

04-W07

Description

2/4

2.1.2

Warning and caution signs

This sign, attached to the drive cover, indicates the
direction of rotation of the pump when viewed from the
drive end.

THERE IS RISK OF SERIOUS DAMAGE TO THE PUMP IF IT IS

ALLOWED TO ROTATE IN THE WRONG DIRECTION

.

This sign is a hazard warning and is usually
accompanied by text indicating the nature of the hazard.

THERE IS RISK OF SERIOUS INJURY IF THESE WARNING

INSTRUCTIONS ARE NOT OBSERVED

.

The V-belt guard must always

be mounted during operation

WARNING

The sign is mounted on the V-belt guard.

The guard should always be
fitted when the pump is in
operation.

If the guard is to be removed,
check that the motor is
disconnected from the mains
or that the main switch is
turned off and locked so that
the motor cannot be started
inadvertently.

The guard must always be
refitted before the pump is
started.

This sign is attached to a direct-drive coupling guard.

Direction of rotation of the pump is indicated by this sign
attached to the front of the case.

This sign, attached to the frame, indicates that the pump
requires periodic greasing.

«
...
11
12
13
14
15
...
»

Содержание 25411801001/A5684






















































































Отзывы:

Нет отзывов