Metso 25411801001/A5684 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 85

Metso 25411801001/A5684 Скачать руководство пользователя страница 62

Slurry Pump

WH19AM1G410EN_04C.DOC

JAN

04-W08

Care and maintenance

3/4

f)

Smear three new packing rings with grease and then insert into expeller ring
(G7); one turn of packing (G5), lantern ring (G1), the last two packing rings,
followed by gland follower (G10).

NOTE

:

MAKE SURE THAT THE PACKING JOINTS ARE STAGGERED BY APPROXIMATELY

180

°

TO

PREVENT A LEAKAGE PATH FROM OCCURRING

(

SEE

F

IGURE

9.5.3-1).

IF NECESSARY

USE THE GLAND FOLLOWER TO PRESS EACH TURN OF PACKING INTO POSITION

.

g)

Grease the gland through grease nipple (G21).

h)

After opening the inlet and outlet valves check the gland for leaks. If leakage is
excessive tighten the gland follower evenly until leakage is acceptable.

CAUTION

DO NOT

OVER

-

TIGHTEN THE SCREWS AS THIS WILL CAUSE SEVERE WEAR OF THE SHAFT

SLEEVE

.

5.

Maintenance of the Centrifugal Seal (Removal)

a)

Gain access to expeller ring (G7) and gland by opening up the pump using the
Front or Back Pull-Out Method.

b)

Remove expeller (G15).

c)

Slide expeller ring (G7) complete with the gland seal assembly from the shaft.

WARNING

SHAFT SEALS FOR LARGE PUMPS ARE QUITE HEAVY

.

USE THE SPECIAL SHAFT EXTENSION TO

FACILITATES THEIR REMOVAL AND REFITTING

–

SEE SUB

-

SECTION

9.3

.

d)

Remove shaft sleeve (G2) and gaskets (G58) if these items have not come
away with the gland seal.

6.

Maintenance of the Centrifugal Seal (Disassembly)

a)

Remove gland follower screws (G18) and gland follower (G10).

b)

Push out shaft sleeve (G2) if it is still in position.

c)

Remove packing rings (G5) and lantern ring (G1).

7.

Maintenance of the Centrifugal Seal (Inspection)

a)

Inspect expeller ring (G7) and its seal (G17.1) for wear and/or damage.

b)

Examine all gaskets for deterioration, wear and/or damage.

c)

Check shaft sleeve (G2) for wear and/or damage.

d)

Examine gland follower (G10) for distortion of the flange due to over-tightening
of the screws.

e)

Inspect the lantern ring for wear and/or damage.

«
...
60
61
62
63
64
...
»

Содержание 25411801001/A5684






















































































Отзывы:

Нет отзывов