Metal-Fach GHT Скачать руководство пользователя страница 28

28

 

  remove the wrong tank fuel  

7. 

Increase in feeder chamber 

temperature 

  spring failure of the feed flap 

(fig. 1) 

  verify the spring condition of 

the feed flap and sight glass 
cover 

  check the temperature level 

on the controller 

8. 

Feeder circuit" message on 

the controller display 

  Mechanical damage to the 

sensor or contamination of 
the piston dead centre 
sensor (Hall sensor) 

  clean the magnet 

underneath the sensor from 
accumulated dirt 

9.  

Water course around the 

boiler 

  leakage of central heating 

installation 

  check the condition of the 

furnace 

  check the status of the c. o. 

installation. 

  after repairing the leak, top 

up the water in the system  

  opening fire protection 

"Firefighter" 

  Wear protective rubber 

boots to avoid electrocution 

  disconnect the boiler from 

the electrical installation 

  restore the boiler to its 

original state or call the 
service 

10. 

Boiler does not reach the set 

operating temperature 

  use of the wrong fuel 

  fuel with too high a humidity 

above 30%. 

  dirty combustion chamber, 

obstructed head ventilation 
openings 

  inappropriate controller 

settings 

  replace the fuel with one 

recommended by the 
manufacturer 

  Set the correct feeding and 

stopping times 

11. 

Excessively loud feeding team 

work 

  defective electric motor 

bearing 

  a foreign body in the feeding 

chamber (e.g. metal) 

  excessively polluted fuel 

(e.g. sand) 

  perform the procedure to 

stop the boiler operation call 
the service 

  perform the procedure of 

emergency stopping of the 
boiler, remove impurities 

  fuel transition 

12. 

Controller, does not display 

messages on the display 

  controller failure 

  power cord damage 

  burning of the controller's 

fuses (picture 5) 

  disconnect the boiler from 

the electrical installation 

  check the condition of the 

fuses of the controller 

  check the condition of 

electric wires 

8 Spare parts 

8.1 List of main spare parts 

N. 

Name of the part 

Guarantee period 

Part No. 

Electric motor with geared motor 

2 years 

Содержание GHT

































Отзывы: