manualshive.com logo in svg

MERRICK MC3 90.10.EX, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
MERRICK MC3 90.10.EX Скачать руководство пользователя страница 13

 

MC³ 90.10.EX O&M Manual  

 

- 6 -  

recommends that the controller should be located out of direct sunlight and away from dripping 
water and must be protected from heavy rain.   

The wall mount enclosure is available in NEMA-4 or NEMA-12 boxes.  NEMA-4 box includes 
gaskets and a window kit over the touch screen to provide extra protection.  

Installation 

Mount the controller on a vertical surface, Use dimensions provided in Wall Mount – Mounting 
Dimensions on page  50 for placement of hardware used to secure enclosure to surface.  Make 
sure there is adequate clearance around the unit for swinging open the door and for 
maintenance. 

Door Mount 

A door mount enclosure is available that separates the power-supply and Backplane boards from 
the controller.  This style includes a window for  protection from the elements.  It also adds two 
fans to the cover of the enclosure to improve air circulation for better cooling. 

 

The Merrick MC³ Door Mount Controller is designed for mounting in a control panel.  It is suitable 
for use in environments that are generally clean, and within the temperature range of 32º to 122º 
F (0º to 50º C).  It must be protected from all but incidental water or significant dirt or dust.   

 

Installation 

Mount the controller in the panel. Cut panel to dimensions provided in Door Mount - Dimensions 
on page  51.  Insure there is adequate clearance around the controller for maintenance and 
ventilation.  Install the controller into panel using the mounting brackets provided. 

Electronic Cards 

Backplane Board 

Most of the Digital I/O connections to the MC³ will be made through the Back plane Board.  The 
Back plane mounts vertically in the rear access cover on the Panel mount type enclosure.  On the 
Wall mount enclosure, the boards are mounted directly below the Card stack assembly.  When 
the Door Mount controller is used, the boards are normally placed on a panel inside the cabinet. 

There are two types of Back plane cards available, a dry contact enclosure input card (BPLN) and 
an AC input card (BPAC).  The BPLN card has four dry contact inputs and 7 relay (N/O) outputs.  

Содержание MC3 90.10.EX




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды