12
230V~
+/- 10%
50Hz
Model
CM475
Ω
8.2
+
+
+
+
+ +
open/öffnen/ouvrir/open
open/öffnen/ouvrir/open
close/schliessen/fermer/sluiten
close/schliessen/fermer/sluiten
PHO1
PHO2
Radio
433MHz
LOOP DETECTOR (OPTIONAL)
Jumper OPEN/PED must be plugged
Loop detectors react to metal and the most common use is for cars
or trucks but not for bikes or pedestrians.
Exit loop / Gate Opening Loop
An exit loop is behind the gate and opens the gate when closed,
keeps it open or re-opens the gate.
The jumpers OPEN/PED must be PLUGGED (in place).
The gate requires installed photocells and timer to close activated.
In addition, the feature “Fast closing” can be activated.
Refer to section “Description of Push Buttons P1, P2 & P3”
30VDC
MOTOR
MASTER
MOTOR
SECOND 24V/150mA
BRN GRN WHT YEL
MASTER
BRN GRN WHT YEL
SECOND
COM
PHOTO
3 2 1
COM
EDGE
8.2KΩ
STOP
PHO 1
PHO 2
PED
EDGE
CH1
CH2
1/
2
M
OT
OR
P1
P2
P3
L
N
POWER SUPPLY
230VAC/50Hz
TR
AN
SF
23
0V
AC
INPUT 24VAC
250V/2A
250V/2A
OP
EN
/S
TE
P
LI
GH
T/
SP
Y
OB
ST
AC
LE
SP
EE
D
1
SP
EE
D
2
RA
DI
O
PHO 3
LEARN
DGN
LIGHT
CONTACT
PED
COM
STOP
NO
Model
203292
Model
203292
8,2kOhms
30VDC
MOTOR
MASTER
MOTOR
SECOND 24V/150mA
BRN GRN WHT YEL
MASTER
BRN GRN WHT YEL
SECOND
COM
PHOTO
3 2 1
COM
EDGE
8.2KΩ
STOP
PHO 1
PHO 2
PED
EDGE
CH1
CH2
1/
2
M
OT
OR
P1
P2
P3
L
N
POWER SUPPLY
230VAC/50Hz
TR
AN
SF
23
0V
AC
INPUT 24VAC
250V/2A
250V/2A
OP
EN
/S
TE
P
LI
GH
T/
SP
Y
OB
ST
AC
LE
SP
EE
D
1
SP
EE
D
2
RA
DI
O
PHO 3
LEARN
DGN
LIGHT
CONTACT
PED
COM
STOP
NO
COM
NC
OPEN/PED
230V~
+/- 10%
50Hz
Model
CM475
Ω
8.2
+
+
+
+
+ +
open/öffnen/ouvrir/open
open/öffnen/ouvrir/open
close/schliessen/fermer/sluiten
close/schliessen/fermer/sluiten
PHO1
PHO2
Radio
433MHz
Jumper ON
RADIO AND RADIO PROGRAMMING
Insert radio module on designated pins, if not pre-installed.
PROGRAM / DELETE REMOTE CONTROLS
The receiver has two channels CH1 and CH2.
The respective LEDs CH1 and CH2 are assigned to these two channels.
Receiving a signal from a programmed remote control button, CH1 fully
opens the gate.
Receiving a signal from another programmed remote control button,
CH2 partially opens the gate (pedestrian mode).
PROGRAMMING
1.
Insert (connect) jumper “RADIO”
2. Briefly push button P1 (for CH1) or P2 (for CH2) and the respective
LED lights up.
3. Press and hold a selected button on your remote control until LED
goes out after short flashing. Done!
Repeat for all remote controls (a maximum of 180 remote controls
can be programmed to each channel).
Important:
To finish programming, remove (disconnect) jumper “Radio”!
Note:
Make sure
NOT
to program the same remote control button to
CH1 and CH2, otherwise the gate will
NOT
work properly.
DELETE
1. Insert (connect) Jumper “Radio”.
2. Press and hold buttons P1 (for CH1) or P2 (for CH2) until the
respective LED goes out again (approx. 10 seconds).
Single remote controls can not be deleted. All remotes programmed
to this channel are deleted.
Important:
To finish deleting, remove (disconnect) jumper “Radio”
