This sliding gate motor can be activated by hardware trigger inputs (keyswitches, keypads or induction
loops) as well as via the RF remote controls provided. The control board provides a variety of safety and
operating functions. Please familiarise yourself with these function to ensure the safest and most functional
automation of your gate.
A set of manual release keys is provided with your motor incase of power failure.
PLEASE LABEL THESE KEYS AND STORE IN A SAFE PLACE.
3
CONTENTS
PAGE
SAFETY INSTRUCTIONS . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . .3
CARTON CONTENTS . . . . . . . . . . .3
INSTALLATION . . . . . . . . . . . . . .4-6
TYPICAL CONFIGURATION . . . . . .7
INSTALLATION OF CONTROL
BOARD . . . . . . . . . . . . . . . . . . . . . .7
WIRING OF CONTROL BOARD 8-10
ACCESSORIES . . . . . . . . . . . .11-12
JUMPER SETTINGS . . . . . . . . . . .13
INITIAL OPERATION/BASIC
SETTING . . . . . . . . . . . . . . . . . . . .14
PROGRAMMING THE TRAVEL
DISTANCE AND OPERATOR
FORCE . . . . . . . . . . . . . . . . . . . . .15
COMPLETION OF INSTALLATION/
PROGRAMMING . . . . . . . . . . . . . 16
SPARE PARTS . . . . . . . . . . . . . . .17
DIAGNOSIS LED . . . . . . . . . . . . . .18
FREQUENTLY ASKED
QUESTIONS . . . . . . . . . . . . . . . . .19
WARRANTY . . . . . . . . . . . . . . . . .20
BEFORE YOU BEGIN
• Ensure the gate is in working order and suitable for automation.
Check that any wheels are in good working order, the track is free from obstruction and that the gate moves
smoothly throughout itʼs travel. If not, have the gate serviced by a gate installer.
• Ensure the motor you are installing is suitable for the gate weight and duty cycle.
Operating frequency / Duty cycle:
MGS Sliding gate drives have a maximum duty cycle of approx. 30% (i.e. 30% per
hour) and not intended for commercial applications.
CAUTION:
This device is not intended to run in high duty cycle applications, frequent activations may engage the units
thermal overload circuit. When this occurs the unit will cease operations until such time as the motor cools.
• Gate size:
When calculating the gates weight allow for the gateʼs length, a light weight long gate (long = 5m or more)
needs far greater force to set it in motion than a short gate or heavy gate.
• Gate weight:
Ensure that allowance is made not only for the gateʼs weight but its length and mobility.
Example: A light gate that slides poorly is likely to need a stronger drive than a heavy, smooth-sliding gate.
NOTE: Gate weight is only an approximate indicator, the actual relevance of which can vary greatly.
• Climatic conditions
. Gate operating in high wind areas may be affected by side pressure on the gate. Timber or
metal lined gates may require additional force to operate in high winds. It is essential that this is allowed for before
installation.
• Temperature:
Extreme low outdoor temperatures can make it difficult to operate the gate due to changes in the
ground conditions. A higher powered again might be necessary.
High outdoor temperatures can cause the thermal protection mechanism to be activated sooner.
• Safety:
Your CB202 control board has outputs for flashing lamp as well as safety inputs for, contact strips, loop detectors
and photo electric safety beams (1 set of PE beams is provided). Please ensure that you comply with the standards and
regulations relevant to your particular installation.
• Control unit:
The control unit was developed specifically with safety aspects in mind.
It is located in the motor
housing.
041SLG-125SA
located under the
motor cover.
• PE safety beams (1 set)
• Hardware bag
• Merlin C945 Mini remotes x 2
• Motor with housing
• PCB CB202 logic board
• Limit magnets (1&2) and
mounting accessories
• Base plate
MGS524 Carton contents
