Meritor MM-0861 Скачать руководство пользователя страница 79

Страница: 79 / 118

MM-0861 / Revised 06-22

Page 77

Printed in USA

7 Assembly

4007109a

SPEED

SENSOR

FRONT AXLE

DECLUTCH PORT

MTC-4208XL/XLEV/XLEC AND MTC-4210XL/XLEV/XLEC

Figure 7.49

4. On MTC-4208XP and MTC-4210XP, install the PTO

engagement and disengagement switch assemblies, if
equipped. Otherwise, install a nut and washer into the open
port.

5. Reinstall all other pipe threaded plugs using Loctite

592

threadlocker.

Oil Cooler Connections

1. Reinstall the male connector fittings, if removed. Apply

Loctite

592 threadlocker to the pipe threads. Tighten the

fittings to 25 lb-ft (34 Nm).

2. Connect the oil cooler lines:

• MTC-4213X, MTC-4208X/XP, and MTC-4210X/XP, PTO

Ready:

Reconnect the loop line. Tighten the fittings to 20

lb-ft (27 Nm).

• MTC-4208XL/XLEV and MTC-4210XL/XLEV with Rear-

Mounted Pump:

Reconnect the tube between the pump

outlet and front idler bearing orificed elbow.

• MTC-4208XLEC and MTC-4210XLEC:

Refer to the

instructions on page 90 for oil tube installation.

Transfer Case Shifting Check

1. Apply 60 psi (4.14 bar) or greater of air pressure to the front

axle declutch. Figure 7.49.

2. Turn the input shaft by hand to verify the front output turns at

same rate as the rear output.

3. Remove the air pressure.

4. Apply 60 psi (4.14 bar) or greater of air pressure to the high-

range shaft air port. Figure 7.50.

MTC-4208XP AND MTC-4210XP SHOWN

4000218c

AIR

CONTROL

PORT

NEUTRAL

PORT

HIGH RANGE

SHIFT PORT

LOW RANGE

SHIFT PORT

BLOW-BY

BREATHER

Figure 7.50

5. Turn the input shaft by hand to verify the rear output turns at

same rate as the input.

6. Remove the air pressure.

7. Apply 60 psi (4.14 bar) or greater of air pressure to the low-

range shaft cylinder air port. Figure 7.50.

8. Turn the input shaft by hand to verify the rear output turns at

approximately half the rate as the input.

9. Remove the air pressure.

10. For PTO-equipped cases, apply 60 psi (4.14 bar) or greater of

air pressure to the neutral shift location. Figure 7.50.

11. Turn the input shaft by hand to verify the rear output does not

turn at all. Have someone hold the output shafts to prevent
them from turning while spinning the input.

12. Remove the air pressure.

13. Remove the transfer case from the stand.

Содержание MM-0861























































































































Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды

Meritor MM-0861, Руководство по обслуживанию

Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды