manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 51

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 49

Printed in USA

5     Disassembly

4000192a

OUTER

SHIFT

PISTON

Figure 5.19 

5.  To remove the inner piston, reinstall and hand-tighten the 

shift cylinder. Apply air to the high gear input port. When the 
air pressure pushes the inner piston UP, remove the snap ring 
and inner piston. Figure 5.20.

4000193b

INNER
SHIFT
PISTON

Figure 5.20 

Split the Case Halves

1.  Remove the capscrews securing the rear cover to the front 

case.

 CAUTION

When using a pry bar, be careful not to damage the carrier or 
housing flange. Damage to these surfaces will cause oil leaks.

2.  Use a pry bar to separate the two halves of the transfer case 

at the pry tab locations around the case.

3.  Place eyebolts into the rear cover lift holes located at the top 

and bottom of the cover.

 DANGER

Follow all safety guidelines and instructions provided by the lifting 
device manufacturer. Check that the lift capacity marked on the 
lifting device, straps and chains is correct for the weight being 
lifted. If they are not marked with the lift capacity, do not use 
them. Inspect lifting straps to ensure they are not damaged. 
NEVER subject lifting straps to shocks or drop-loading. Failure to 
follow these directives can result in death or serious personal 
injury and damage to components.

 CAUTION

As the rear cover is lifted, apply DOWNWARD pressure on the 
shift rod to prevent the gears from dropping out of the rear 
transfer case half.

4.  Attach a suitable lifting device to the eyebolts. Lift the rear 

cover from the front case. Figure 5.21.

4018993a

LIFT USING

EYEBOLTS

Figure 5.21 

5.  As the rear cover is lifted, verify the high and low shift shaft 

remains in the case by placing pressure on the shaft while 
separating the transfer case halves.

6. 

MTC-4213X Only:

 The rear output shaft and high-range gear 

are removed as an assembly along with the rear cover. The 
shaft is pressed into the bearing assembly which keeps the 
shaft retained in the housing. Refer to “Disassemble MTC-
4213X Rear Output Shaft Assembly” on page 50.

7. 

MTC-4208X/XP/XL/XLEV/XLEC and MTC-4210X/XP/XL/
XLEV/XLEC Only:

 Remove the high range helical gear. 

8.  Remove the high and low shift fork, shift shaft, and clutch 

collar from the front case. Figure 5.22.

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды